579640

Black Decker CS355 T1 Manual

7
Zoom out
Zoom in
Previous page
1/100
Next page
7
ENGLISH
(Original instructions)
u Replace the cutting disc (J). Make sure that the new disc
is placed onto the spacer (R) in the correct rotational
direction.
u Secure the blade with the retaining ange (U), the washer
(T) and the bolt (S).
u Push in the spindle lock (L).
u Rotate the cutting disc (J) until it locks.
u Using the at wrench (G), tighten the bolt (S) by turning
clockwise.
u Move the guard back down and release the spindle lock
(L).
u Adjust the cutting depth as necessary.
Adjusting the cutting depth (g. 1)
The cutting depth can be adjusted to meet the wear of the
cutting disc.
u Make a dry run with the tool switched off and check for
clearance.
u If adjustment is required, proceed as follows:
u Loosen the lock nut (M) a few turns.
u Turn the depth stop bolt (M) in or out as to achieve the
required cutting depth.
u Tighten the lock nut (M).
Warning: Always adjust the depth stop to its original position
when replacing the cutting disc.
Clamping the workpiece in position (g. 2 - g 4)
The tool is equipped with a vise (F)
u Pull the lever (I) toward the handle (H).
u Push the vise (F) forward until the jaw is almost touching
the workpiece.
u Press the lever (I) toward the jaw until it engages with the
clamp shaft.
u Rotate the handle (H) clockwise and clamp the workpiece
securely.
u To release the workpiece, rotate the handle (H)
counterclockwise.
u To increase the cutting capacity, place a spacer block
under the workpiece. The spacer block should be slightly
narrower than the workpiece.
Warning: Support long workpieces using a piece of wood. Do
not clamp the cut off end.
Quick travel feature (g. 4)
The clamp has a quick travel feature.
u To release the clamp, rotate the handle (H) one or two
turns counterclockwise and pull the lever (I) toward the
handle (H).
Setting the clamping position (g. 5)
The clamping position can be set to match the cutting disc.
u Remove the fence bolts (P) using the at wrench (G).
u Move the fence (E) as required.
u Re-t the fence bolts (P) and tighten them to lock the
fence (E).
Adjusting the angle of cut (g. 6)
The tool can be used for mitre cuts up to 45°.
u Loosen the fence bolts (P) to release the fence (E).
u Set the fence (E) to the required angle. The angle can be
read on the scale (Q).
u Tighten the fence bolts (P) to lock the fence (E).
Checking and adjusting the mitre scale (g. 6)
u Loosen the fence bolts (P) to release the fence (E).
u Pull down the arm and lock it in this position by attaching
the lock chain (A).
u Place a square against the fence (E) and the left side of
the cutting disc creating a perfect 90°. Check that the 0°
marking on the scale (Q) aligns with the marking on the
base (D).
u Tighten the fence bolts (P) to lock the fence (E).
u Remove the lock chain (A) and return the arm to its upper
rest position.
Adjusting the spark deector (g. 1)
u Loosen the screw (B).
u Set the spark deector (C) as appropriate.
u Tighten the screw (B).
Use
Warning: Always observe the safety instructions and
applicable regulations.
Warning: Do not apply excessive pressure to the tool.
Warning: Avoid overloading. Should the tool become hot, let
it run a few minutes under no load condition.
Cutting capacity
The wide vise opening and high pivot point provide cutting
capacity for many large pieces. Use the cutting
capacity chart to determine total maximum size of cuts that
can be made with a new wheel.
Caution: Certain large, circular or irregularly shaped objects
may require additional holding means if they cannot be held
securely in vise.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker CS355 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CS355 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker CS355 T1

Black Decker CS355 T1 Quick start guide - English - 12 pages

Black Decker CS355 T1 User Manual - Polish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info