Manual Black Decker CS355 T1 (page 6 of 100) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

579640

Zoom out

Zoom in

1/100

ENGLISH

(Original instructions)

u Regularly clear the ventilation slots when working in dusty

conditions. If it should become necessary to clean the

slots, remember to unplug the tool rst.

u Always store cutting discs well-protected and in a dry

place, out of reach of children.

u Warning!Use of this tool can generate dust containing

chemicals known to cause cancer, birth defects or other

reproductive harm. Use appropriate respiratory protection.

Warning! Only use a chop saw wheel with a

maximum thickness of 3 mm and a maximum

diameter of 355mm.

Warning! The cutting wheel will continue to rotate after the

tool has been switched off.

u Use only reinforced wheels rated 4300 rpm or higher.

u Always wear eye protection, use guards, clamp work in

vise, use proper respiratory protection.

The following factors are of inuence to noise production:

u the material to be cut

u the type of the cutting disc

u the feed force

u Warning!Take appropriate measures for the protection of

hearing.

Residual risks

The following risks are inherent to the use of these

machines:

u injuries caused by touching the rotating parts

u injuries caused by disruption of the cutting disc

These risks are most evident:

u within the range of operation

u within the range of the rotating machine parts

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided. These are:

u Impairment of hearing.

u Risk of accidents caused by the uncovered parts of the

rotating cutting disc.

u Risk of injury when changing the disc.

u Risk of squeezing ngers when opening the guards.

Electrical safety

Your tool is double insulated; therefore no earth

wire is required. Always check that the mains

voltage corresponds to the voltage on the rating

plate. Never attempt to replace the charger unit

with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Voltage drops

Inrush currents cause short-time voltage drops.

Under unfavourable power supply conditions, other

equipment may be affected.

If the system impedance of the power supply is lower

than 0.12 Ω, disturbances are unlikely to occur.

Warning Symbols

The following symbols are found on the tool:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Always wear safety goggles.

Always wear safety hearing protection.

Features

This tool includes some or all of the following features.

A. Lock Chain

B. Spark deector screw

C. Spark deector

D. Base

E. Fence

F. Vice

G. Flat Wrench

H. Crank

I. Vice Lever

J. Cutting disc

K. Guard

L. Spindle Lock

M. Depth Stop Bolt and Locking Nut

N. Trigger Switch

O. Padlock Hole

P. Fence Bolts

Assembly

Warning! Turn off and unplug the tool before making any

adjustments or removing or installing attachments or

accessories. Be sure the trigger switch is in the OFF position.

Do not make any adjustment while the wheel is in motion..

Removing and tting a cutting disc (g. 7 - g 8)

u Push in the spindle lock (L).

u Rotate the cutting disc (J) until it locks.

u Using the at wrench (G), remove the bolt (S) by turning

counterclockwise and then remove the washer (T) and the

retaining ange (U).

u Check that the spacer (R) is in place against the ange.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CS355 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker CS355 T1

Black Decker CS355 T1 Quick start guide - English - 12 pages

Black Decker CS355 T1 User Manual - Polish - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker CS355 T1 Manual

Product: