Manual Black Decker CLM3820 T1 (page 11 of 164) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

586103

Zoom out

Zoom in

1/164

ENGLISH

(Original instructions)

The charger is intended for

indoor use only.

Read the instruction manual

before use.

Electrical safety

Your charger is double insu-

lated; therefore no earth wire is

required. Always check that the

mains voltage corresponds to the

voltage on the rating plate. Never

attempt to replace the charger

unit with a regular mains plug.

If the supply cord is damaged, it must

be replaced by the manufacturer or

an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This appliance includes some or all of the following features.

1. Safety key

2. Bail bar

3. Lock off release

4. Handle bar

5. Cable restraint clips

6. Upper handle

7. Upper handle quick release clamp

8. Grass box full indicator

9. Grass collection box

10. Lower Handle

11. Lower handle quick release clamp

12. Spring loaded rear door

13. Height adjust handle

14. Battery cover

15. Battery cover release

16. Handle

Assembly

Warning! Before assembly, make sure that the tool is

switched off and the safety key and battery have been

removed.

Assembling the grass collection box (g. A - C)

The grass box requires assembly before use and comes in 3

pieces.

u Clip the 2 sides of the grass collection box (9) together

(g.A). Make sure that all clips and guides are aligned.

u Align the lid (17) onto the assembled grass collection box.

Ensure that the guides and clips are aligned.

Note: Take extra care when aligning the clips at the rear of the

grass collection box.

u Push down on the lid to secure all clips. Begin at the

front and work towards the back. Ensure that all clips are

securely located.

Fitting the lower handle (g. D & E)

u Remove the lower handle quick release clamps (11) from

the base of the mower.

u Place the lower handle (10) around the base, making

sure the three notches (18) on the lower handle (10) face

toward the top.

u Screw the lower handle quick release clamps (11) through

the lower handle into the mower base, With the lower

handle quick release clamps screwed in half way, close

the quick release clamps (g.E) and ensure the teeth of

the handle and base interlock. If the connection between

the handle and quick release clamps is too tight or loose,

adjust the depth of the quick release clamps and close

them again until the teeth are fully closed.

Fitting the upper handle (g. F & G)

u Fit the upper handle (6) to the lower handle (10) using the

upper handle quick release clamps (7) and clamp nuts

(19) as shown.

u Screw the upper handle quick release clamps (7) through

the lower handle into the clamp nuts (20), With the

upper handle quick release clamps screwed in half way,

close the quick release clamps (g. G). If the connection

between the handle and quick release clamps is too tight

or loose, adjust the depth of the quick release clamps and

close them again until the teeth are fully closed.

Adjusting the height of the handle (g. H)

u Release the lower handle quick release clamp as shown.

u Lift or lower the handle into one of the 3 marked positions

next to the lower handle quick release clamps.

u Close the lower handle quick release clamps (11) and

ensure the teeth of the handle and base interlock. If the

connection between the handle and quick release clamps

is too tight or loose, adjust the depth of the quick release

clamps and close them again until the teeth are fully

closed.

Securing the motor cable

The motor cable has to be xed using the cable restraint.

u Secure the cable to the upper and lower handle by cliping

it into the cable restraint clips (5)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CLM3820 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker CLM3820 T1

Black Decker CLM3820 T1 Quick start guide - English - 20 pages

Black Decker CLM3820 T1 User Manual - Polish - 24 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker CLM3820 T1 Manual

Product: