Manual Black Decker BES700 (page 13 of 148) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709449

Zoom out

Zoom in

1/148

ENGLISH

(Original instructions)

Changing or installing a new saw blade (Fig. I,

J, K)

Warning! To reduce the risk of serious personal injury, turn

off the tool and disconnect it from the power source before

attempting to move it, change accessories or make any

adjustments.

Warning! Never depress the spindle lock (31) button while the

blade is under power or coasting.

Warning! Do not cut ferrous metal (containing iron or steel) or

masonry or ber cement product with this mitre saw.

Removing the blade

uUnplug the saw.

uRaise the arm to the upper position and push the guard

(14) up as far as possible.

uLoosen, but do not remove guard bracket screw (13c) until

the bracket can be raised far enough to access the

blade screw (13a). Lower guard will remain raised due to

the position of the guard bracket screw as shown in

gure I.

uDepress the spindle lock button (31) while carefully

rotating the saw blade by hand until the lock engages as

shown in gure J.

uKeeping the button depressed, use the other hand and

the blade changing tool provided (30) to loosen the blade

screw (13a). (Turn clockwise, left-hand threads.)

uRemove the blade screw (13a), outer clamp washer

(13d), blade (13) and blade adapter (13e), if used. The

inner clamp washer (13f) may be left on the spindle.

Installing a blade

uUnplug the saw.

uWith the arm raised, the guard held open and the guard

bracket raised, place the blade on the spindle, onto the

blade adapter and against the inner blade clamp with the

teeth at the bottom of the blade pointing toward the back

of the saw.

uAssemble the outer clamp washer onto the spindle.

uInstall the blade screw and, engaging the spindle lock,

tighten the screw rmly with wrench provided (turn coun-

terclockwise, left-hand threads).

Adjusting the mitre angle (Fig. L)

uLoosen the grip (9) by turning counterclockwise.

uUse the mitre lock release (32) to move the rotary table

(11) to the position where the pointer (7) points to the

desired angle on the mitre scale (26), tighten the grip

clockwise.

uThe adjustable support foot (24) is to help keep the tool in

balance. After each mitre angle adjustment, you should

turn knob on the foot clockwise or counterclockwise until

its bottom touches the ground. There are two positions

depending on the depth of your work bench.

Cutting depth

If you want to cut a groove you can set the depth of cut using

the depth of cut screw (29) or the blade.

uTurn the depth of cut screw (29) and x with the counter

nut.

Fence adjustment

Before bevel cutting, make sure that no part of the tool

contacts the fence (12) when lowering and raising the handle

fully at any position and pulling or pushing the carriage all the

way at the lowest position. Before operating the tool, make

sure that the sliding fence is secured by the slide nce locking

screw (35) rmly.

Warning! When performing bevel cuts, slide the sliding fence

to the left and secure. Otherwise, it will contact the blade or a

part of the tool, causing possible serious injury to the operator.

This tool is equipped with the sliding fence which should

ordinarily be positioned central. However, when performing left

bevel cuts, set it to the left position if the tool head contacts it.

When bevel cutting operations are complete, don't forget to

return the sliding fence to the original position and secure it by

rmly tightening the slide fence locking screw (35).

Adjusting the bevel angle (Fig. M)

When tilting the carriage to the left, loosen the lever (2) at the

rear of the tool counterclockwise. Unlock the arm by pushing

the handle somewhat strongly in one direction only.

uTilt the saw blade until the pointer (25) points to the

desired angle on the bevel scale (27).

uTighten the lever (2) clockwise rmly to secure the arm.

Warning! When tilting the saw blade, be sure to raise the

handle fully. After changing the bevel angle, always secure the

arm by tightening the lever clockwise.

Warning! When tilting the saw blade, always be aware of the

weight of the head and make sure to avoid it crashing over.

Switch action (Fig. N)

Caution! Before plugging in the tool, always check to see that

the switch trigger (19) actuates properly and returns to the

"OFF" position when released.

u To start the tool, move the safety release lever (20) to the

right with your index nger.

u Press the switch trigger (19).

u To stop the tool, release the switch trigger (19).

Warning! Never use tool without a fully operative switch

trigger. Any tool with an inoperative switch is

HIGHLY DANGEROUS and must be repaired before usage.

Use of Cut line System (Fig. N)

Note: The mitre saw must be connected to a power source.

The Cut line System is equipped with an on/off switch (21).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BES700 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker BES700 Manual

Product: