Manual Black Decker BES700 (page 12 of 148) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709449

Zoom out

Zoom in

1/148

ENGLISH

(Original instructions)

Table extension rail (Fig. C & D)

Your mitre saw is supplied with 2 table extension rails (5) to

support long overhanging workpieces.

uPull the table extension rail (5) to the required length for

the workpiece as shown in gure C.

uSecure in position by tightening the extension rail locking

screw (33), as shown in gure D.

uRepeat the process on opposite side.

Support stand - BES710 only (Fig. E)

Your BES710 mitre saw is supplied with 1 support stand (3),

located at the rear of the unit, to enhance stability.

Bench mounting (Fig. F)

The mitre saw can be bolted with four bolts (6a) (not provided)

to a level and stable surface using the bolt holes (6) provided

in the tools base. This will help prevent tipping and possible

injury.

Dust collection (Fig. G)

The use of the dust bag (23) makes cutting operations clean

and dust collection easy.

u To attach the dust bag (23), t it onto the dust nozzle

(23a).

u When the dust bag (23) is about half full, remove it from

the tool.

u Empty the dust bag of its contents, tapping it lightly so as

to remove particles adhering to the insides which might

hamper further collection.

Note: If you connect a workshop vacuum to your saw, more

efcient and cleaner operations can be performed.

To install workpiece clamp (Fig. H)

uInsert the clamp (4) into the hole (4c) behind the

fence. The clamp should be facing toward the

back of the miter saw. The groove on the clamp

rod should be fully inserted into the base. Ensure

this groove is fully inserted into the base of the

miter saw. If the groove is visible, the clamp will

not be secure.

uRotate the clamp 180º toward the front of the

miter saw.

uLoosen the knob (4b) to adjust the clamp up or down,

then use the ne adjust knob (4a) to rmly clamp the

workpiece.

Note: Place the clamp on the opposite side of the base when

beveling. ALWAYS MAKE DRY RUNS (UNPOWERED) BE-

FORE FINISH CUTS TO CHECK THE PATH OF THE BLADE.

ENSURE THE CLAMP DOES NOT INTERFERE WITH THE

ACTION OF THE SAW OR GUARDS.

2. Bevel lock knob

3. Support stand

4. Work piece clamp

5. Table extension rail

6. Bolt holes

7. Mitre angle indicator

8. Table insert

9. Mitre lock knob

10. Base plate

11. Rotary table

12. Rear fence

13. Saw blade

14. Blade guard

15. Safety guard mounting plate

16. Motor housing

17. Saw head locking pin

18. Main handle

19. Trigger switch

20. Safety release lever

21. Cut line light on/off button

22. Carry handle

23. Dust bag

24. Adjustable support foot

25. Bevel angle indicator

26. Mitre angle scale

27. Bevel angle scale

28. Slide bar locking screw

29. Depth of cut screw

30. Blade change tool

31. Spindle lock

32. Mitre lock release

33. Extension rail locking screw

34. Clamp lock screw

35. Slide fence locking screw

36. Cable wrap

Assembly

Your mitre saw is part assembled in the carton.

uOpen the box and lift the saw out.

u Place the saw on a smooth, at surface such as a work-

bench or strong table.

u Examine Assembly diagram on page 2 of this manual to

become familiar with the saw and its various parts. The

section on adjustments will refer to these terms and you

must know what and where the parts are.

u When the tool is shipped, the handle is locked in the

lowered position by the saw head locking pin (17). Pull

the saw head locking pin (17) and rotate it 90º, either

clockwise or counterclockwise as shown in gure A.

u The mitre locking knob (9) is not assembled for shipping.

Remove the mitre locking knob (9) from the packaging

and screw onto the saw, see gure B for position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BES700 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker BES700 Manual

Product: