Manual Black Decker BDV1084 (page 6 of 100) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

53627

Zoom out

Zoom in

1/100

ENGLISH

At the end of stage 2, the battery charger will automatically

begin stage 3 of the charging process.

Stage 3 - top-off charge

Stage 3 is a top-off charge. The voltage is automatically

regulated and is reduced to a predetermined level while the

current is adjusted for a safe, effective battery charge. At the

conclusion of stage 3, the appliance will beep, signalling the

completion of the charging cycle.

Function pushbuttons (fig. A)

The function pushbuttons on the control panel (3), from left

to right, are:

2/6/10A pushbutton (11) (charge rate selector

step 2). This pushbutton allows the user to select

the charge rate based on the battery size. This

selection and the actual battery charge rate are

monitored by the microprocessor. The battery

charger will stop charging if the rate is too fast or

too slow for the battery size or condition.

Battery voltage pushbutton (10). This

pushbutton enables a check to measure the

battery voltage.

Alternator check pushbutton (9). This

pushbutton enables a five-second check that

measures the battery voltage. This check is

repeated at various electrical load levels and the

tests allow the user to determine if the alternator

can keep up with the loads. It can indicate

whether an alternator service may be required.

Control panel LEDs (fig. A)

The following icons are shown on your battery charger:

Fault LED (5). Lights when any of several faults

are detected, see F01 through F05 Codes as

described in the "Troubleshooting" section, later

in this manual.

Reverse polarity LED (6) - lights when the

battery clamps (4) are incorrectly connected to

the battery terminals.

Battery voltage LED (7) - lights when the

battery voltage pushbutton (10) is pressed.

Alternator good LED (8) - lights when load or

no load checks show that the alternator is

keeping up with the electrical load.

Charge rate selection (fig. A)

X This appliance has three charge rate settings, accessed by

the 2/6/10A pushbutton (11):

- 2 amps: smaller batteries, as in lawn mowers,

motorcycles, etc.

- 6 amps: mid-sized batteries, as in small cars.

- 10 amps: automobiles and light trucks.

X After the battery clamps (4) are correctly connected, plug in

the battery charger to a 230 Vac outlet. The battery charger

will show a circulating pattern on the digital display (2), to

indicate that power has been applied. Select the proper

charge current rate based on battery size.

Charging the battery (fig. A)

X Press the 2/6/10A pushbutton (11), the appliance sounds a

beep and displays the charging current. The battery charger

starts charging at 2 amps automatically if the 2/6/10A

pushbutton (11) is not pressed within 3 minutes after

applying AC power.

X The battery charger will occasionally sound a beep and

display 0.0 during self-test or during the charging stage

changes.

X Pressing the 2/6/10A pushbutton (11) again will advance

the charge rate to 6 A, and again to 10 A. Pressing the

pushbutton (11) again will turn OFF the battery charger

output and the digital display (2) will show 000.

Note: This selection and the actual battery charge rate are

monitored by the microprocessor and the unit will stop

charging if the selected rate is too fast or too slow for battery

size or condition.

X As the battery nears full charge capacity, the unit's output

will automatically drop to a lower charge rate.

X The digital display (2) shows the charge current. To view

the battery voltage, press the battery voltage pushbutton

(10). The battery charger will sound a beep and display the

the battery voltage.

X Press the battery voltage pushbutton (10) again to display

the charge current.

X The digital display (2) shows FUL when the battery is fully

charged.

X Disconnect the ac power cord first, then the negative

clamp, and finally the positive clamp.

Automatic float charging (fig. A)

The automatic float charge feature is ideal for maintaining a

battery. It automatically tops off the battery as required to

keep the battery fully charged all the time.

X Keep the ac power and battery connected when the battery

has been fully charged.

X The battery charger monitors the battery and tops it off as

needed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDV1084 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker BDV1084

Black Decker BDV1084 User Manual - Dutch - 14 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker BDV1084 Manual

Product: