560228

Bissell 1867 Manual

5
Zoom out
Zoom in
Previous page
1/8
Next page
5
w w w . b i s s e l l . c o m 8 0 0 . 2 3 7 . 7 6 9 1
Getting ready continued
3. Twist the quick release cord wrap to unwrap the power cord and plug into a 120-Volt
grounded outlet as described in the Important Safety Instructions, on page 2.
4. The ready light will illuminate when the Steam Mop is ready for use.
NOTE: During the first use it may take several seconds for the Steam Mop to begin
steaming. The water needs to flow through the filter to the heater. The delay will only
occur during initial use or when using a new filter.
Operation
Tip:
Do not attempt to use your Steam Mop without water
in the tank.
2
3
Cleaning hard floors
Your Steam Mop is designed to clean hard flooring such as ceramic tile, laminate, marble, stone and sealed
hard wood floors. Use of your Steam Mop on waxed or some unwaxed floors may result in diminished
glossiness. On surfaces that have been treated with wax, the wax may be removed by the heat and steam
action. Do not use on unsealed wood floors or let unit stand on any wood floor for an extended period of
time. This could cause the wood grain to rise. When using on peel-and-stick vinyl, linoleum or any other
heat sensitive floors, use extra caution. Too much heat can melt down glue in the flooring. For best results
test in an inconspicuous area and check the care instructions from your flooring manufacturer.
1. When the ready light illuminates, begin cleaning by passing over surface while pressing
trigger to emit steam.
2. To sanitize an area of your floor, place the center of the Steam Mop over the spot for a
minimum 15 seconds, but no longer than 20 seconds.
3. When the Steam Mop stops emitting steam, simply remove the water tank, refill, and continue
cleaning.
Carpet Refresher Attachment (select models only)
This accessory is recommended for the refreshing of
carpets. Once the steam mop is cradled in the carpet
refresher attachment, it will easily glide over the carpet.
NOTE: Always be sure a mop pad is in place
before placing in carpet refresher attachment. It is
recommended that only white mop pads be used with
the carpet attachment. Do not use carpet attachment
on spots or stains, or glide it over the same spot for
longer than 20 seconds.
1. Attach the mop pad to the swivel mop head. As
directed in step 1 on page 4.
2. Place the swivel mop head, with mop pad attached, in
the carpet refresher attachment.
Note: that the Steam Mop rests in the carpet refresher
attachment and may not stay attached to the swivel mop
head. It is meant to glide over the carpet.
3. Fill the water tank with water. Begin refreshing your
carpet or rug by pushing the Steam Mop in a forward
and backward motion, releasing steam as you go.
CAUTION:
Never put descaling,
alcoholic, or deter-
gent products into
the steam cleaner,
as this may damage
it or make it unsafe
for use.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bissell 1867 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bissell 1867 in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info