542477

BH Fitness H-491 Manual

10
Zoom out
Zoom in
Previous page
1/33
Next page
10
on the saddle to do the exercises.
The right-hand pedal (12 R), marked
with the letter (R), screws onto the
right-hand crank, also marked with an
(R), in a clockwise direction. Tighten
securely, Fig.6.
The left-hand pedal (12 L), marked
with the letter (L), screws onto the left-
hand crank, also marked with an (L),
in an anti-clockwise direction. Tighten
securely, Fig.6.
Once the pedals have been fitted,
insert the end of the pedal clip (1) into
the slot on the pedal (2) adjusting it to
your footwear on the ledge of the
pedal (3) Fig.7.
5 ATTACHING THE SADDLE.-
Remove the three nuts and washers
from the saddle (19), Fig.8, place the
saddle onto the triangular plate at the
top of the saddle post (16), refit the
washers and nuts and tighten
securely.
6 ADJUSTING SADDLE
HEIGHT.-
Loosen the saddle height control knob
(32) a little, Fig.9, turning it anti-
clockwise and then pulling it back,
insert the saddle post (16) into the
hole (v) on the main body (A) and
when it is at the right height release
the control knob and this will lock into
the holes on the saddle post. Tighten
the control knob by turning it
clockwise.
7 FITTING THE HANDLEBAR.-
Line the handlebar (2) up with the
lower holes on the main post (6),
passing the hand-grip cables (Z)
through the inside of the holder in the
direction indicated by the arrow, as
shown in Fig.10, and pulling them out
through the upper hole of the post.
Next, take screw (42) and flat washer
(40), loosened previously and screw
them onto the bottom of the handlebar
(2).
8 FITTING THE ELECTRONIC
MONITOR.-
(MOD H-491). Undo screws (4)
located at the back of the monitor,
then slide the monitor onto the plate at
the top of the main post, Fig.11, put
the two screws (4) back in.
Take the end of the feedback cable (x)
and plug it into the SENSOR INPUT
hole (y) at the back of the monitor,
Fig.11, now take the end of the hand-
grip cable and plug it into the PULSE
INPUT hole (v) .Fig.11.
MOD H-493. Undo screws (4) located
at the back of the monitor, connect
cable (39), sticking up out of the main
post (6), into connector, located at the
back of the monitor (1) Fig.12, then
slide the monitor onto the plate at the
top of the main post (6) Fig.12, put the
two screws (4) back in. Take the end
of the hand-grip cable (z) and plug it
into the PULSE INPUT connector (v)
at the back of the monitor, Fig.12.
9 EXERTION CONTROL.-
Mod. H-491. To provide an even level
of exertion during exercise, this
appliance is equipped with a
tensioning control (W), located on the
monitor housing, offering various
exertion settings, Fig.11.
To increase pedal resistance turn the
tensioning control (W) clockwise (+)
until the exertion level best suits your
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BH Fitness H-491 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BH Fitness H-491 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info