Manual BH Fitness G690 (page 14 of 55) (English, German, Dutch, French, Italian, Portuguese, Spanish)

528801

Zoom out

Zoom in

1/55

SK LINE G-690 / G-690TV

sportkoncept

ATTACHING THE MONITOR

SUPPORT PLATE.-

Take the monitor support plate (Q), passing the

cables through the central hole (O). Use the

holding screws (b) to attach it to the handrail

handlebar.

FITTING THE HANDRAIL

HANDLEBAR.-

NOTE: The assistance of a second person is

recommended when assembling this component

Take hold of the handrail (C) and pass the terminal

(TV on Mod. G-690 Tv) sticking up out of the left

handlebar (D), in through the handrail and bring it

out through central hole (O), Fig.3, next pass

terminal (P), sticking up out of the right handlebar

(E), in through the handrail and bring it out through

central hole (O), Fig.3.

Once this is done, rest the handrail handlebar on

top of the focus bars, making sure not to catch any

of the cables, and attach it securely using nuts (c).

ATTACHING THE MONITOR

Take monitor (A) and connect the terminals k, m

and o, Fig.4, coming out of the monitor, to

terminals l, n, and p coming out of the handrail

handlebar. Next, push all the terminal connections

through the hole in the monitor support plate,

Fig.4, and insert screws (b), making sure not to

pinch any of the cables, and tighten securely.

ATTACHING THE REAR

MONITOR SUPPORT

Take the rear cover for the monitor (F) and place it

into position. Use screws (e) to tighten securely.

LEVELLING.

Once the unit has been placed into its final position

for doing exercise, make sure that the treadmill sits

flat on the floor and that it is level. This can be

achieved by doing the following:

A) – Switch the treadmill on to see if the monitor

shows that the treadmill is at zero inclination level.

B) – Once you have checked this, place a spirit

level on the running belt, Fig.5, and screw the

adjustable feet (V) either in or out to level up the

belt, as shown in Fig.5.

It is advisable to do this by regulating the two

adjustable feet.

MOVEMENT & STORAGE.

The unit is equipped with wheels (W), Fig.6, to

make it easier to move. Make sure that the mains

cable is unplugged from the wall socket. If you

wish to move the treadmill, tilt the treadmill, Fig.6,

so that the wheels (Y) rest on the floor.

NOTE: To prevent accidents DO NOT move the

treadmill across uneven floors.

MAINTENANCE

Use the bottle of lubricant (h) to lubricate the inside

of the belt Fig.6, in order to keep your unit in top

condition and to ensure that friction between the

belt and the board is kept to a minimum (due to

different running styles, always apply more

lubrication to the area where you place your feet

during the exercise).

It is advisable to lubricate the base of the belt

between the board and the band every month,

depending on how often it is used.

If the belt starts to slip after lubrication, then check

the tension of the belt. To tension the belt, Fig.6,

take the Allen key (m) and with the machine set to

4 km/h turn screws (R & L) one full turn in a

clockwise direction.

Do not use solvent based lubricants

ADJUSTING THE BELT

If your unit is not seated evenly on the four contact

points, this may cause the belt (X) to shift

sideways. Rigorous quality control adjusts and

checks the running belt. However, due to weight

differences and individual styles of running, the

belt may be prone to shift sideways.

If the belt does shift to the left or right, stop the

machine.

BELT OFFSET TO THE RIGHT

This procedure is very important. Follow these

steps. In order to adjust the belt, set the unit in

motion at a speed of 4km/h. If the belt has moved

to the right, turn screw (R) on the right-hand side of

the machine a 1⁄4 turn clockwise. Note the position

of the belt, if after one minute the belt is not

completely centred then repeat the operation. If

you see that the belt has moved too far over to the

left then turn the right screw back slightly in an

anticlockwise direction. Fig.7.

As soon as you have adjusted the belt you can

begin exercising again.

BELT OFFSET TO THE LEFT

In the event that the belt has moved to the left, turn

screw (L) on the left-hand side of the machine a 1⁄4

turn clockwise. Note the position of the belt, if after

one minute the belt is not completely centred then

repeat the operation. If you see that the belt has

moved too far over to the right then turn the left

screw back slightly in an anticlockwise direction.

Fig.7.

Important: Overtightening of the belt can lead to a

loss of speed on the machine and even stretch the

belt itself. Bear In mind that one turn of the right

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of BH Fitness G690 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

BH Fitness G690 Manual

Product: