568802
36
Zoom out
Zoom in
Previous page
1/128
Next page
36
5. Flip the power switch on the back of the base unit. The indicator lamp and the energy indicator lamp
are illuminated and the noise of a fan (similar to the noise a hair dryer makes) can be heard.
6. The device is automatically set to the lowest energy level. The device is then ready to emit the first
pulse.
7. The energy selection buttons “+” and “-” can be used to increase or decrease the energy level to set
the energy level determined in the automatic skin tone recognition test and confirmed in the skin sen-
sitivity test and/or to adjust the setting to your requirements. The energy indicator lamps illuminate
green in accordance with the selected energy level.
8. Place the light area of the cartridge on the desired treatment area and make sure it is in full contact
with the skin.
Note
If you press the trigger button and your skin is to dark or too tanned, the indicator lamp on the applicator
illuminates red. In this case, the applicator does not trigger a pulse on this area of skin.
If the applicator does not have sufficient contact with the skin and you press the trigger button, the
indicator lamp on the applicator illuminates orange. In this case, the applicator does not trigger a
pulse on this area of skin either.
9. Press the trigger button. You will see a bright flash, hear a cracking noise and may feel a slight burn-
ing sensation and/or warmth. The beurer SalonPro System features a “flash-glide” function. When
you press and hold the trigger button, a bright flash is automatically triggered every three seconds,
meaning that you do not have to press the trigger button every time.
WARNING
Do not treat the same area of skin more than once per hair removal session!
Treating an area of skin more than once during a single hair removal session can increase the prob-
ability of side effects.
Try to avoid overlapping pulses.
Note
The pulses from the beurer SalonPro System should be applied in rows – beginning at one end of
each row, continuing to the other end. This technique allows better monitoring of the areas of skin
that have already been treated and helps you to avoid treating the same area more than once or
treating overlapping areas of skin. The light area of the beurer SalonPro System is designed in such a
way that it leaves a temporary impression on the treated area of skin. These visible impressions can
be used for precise placement of the next pulse. Additionally, a lengthways marking is located on the
left- and right-hand side of the cartridge that helps you to determine precisely where the light area is
at any time.
10. Remove the applicator from the skin and place it on the next part of the treatment area. When repo-
sitioning the applicator, make sure not to leave any gaps or overlap the treated skin. The device
recharges itself immediately and is ready for the next pulse within three seconds (the indicator lamp
on the applicator continuously illuminates green once again). Repeat the process until the entire
area of skin has been treated.
After treatment using the beurer SalonPro System
Once the hair removal session using the beurer SalonPro System is finished, switch off the device by
flipping the power switch off.
• Unplug the mains cable from the mains socket.
• After each hair removal session, it is recommended that you clean your beurer SalonPro System,
paying particular attention to the light area (see Chapter 9.1 “Cleaning the beurer SalonPro System”).
• After cleaning, it is recommended that you store your beurer SalonPro System in its original box and
keep away from water.
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beurer IPL 10000 plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beurer IPL 10000 plus in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info