568802

Beurer IPL 10000 plus Manual

33
Zoom out
Zoom in
Previous page
1/128
Next page
33
Using skin tone detection
1. To begin skin tone detection, simultaneously press down both energy level selection buttons
(+ and -) for 2 seconds.
2. Skin tone detection is active when the individual energy indicator LEDs light up in sequence from
left to right.
3. Now place the light area of the cartridge on the desired test area and make sure it is in full contact
with the skin.
Note
For your safety, always select the darkest area of skin (e.g. the outer side of the lower leg, back of
the hand on the arm)
Important: Before using on another part of the body, you must take another measurement.
4. Press the trigger button to begin skin tone detection. Skin tone detection can take 1 – 2 seconds.
Note
The device does not trigger any light pulses in skin tone detection mode.
5. If the skin tone measurement is successful, the suitable energy level for your skin tone appears on
the energy indicator lamp. The LEDs of the displayed energy level remain permanently lit.
6. If the energy indicator lamp lights up from left to right as before, skin tone detection was unsuc-
cessful.
7. Check the indicator lamp on the applicator. If the indicator lamp is orange, there was not enough
contact with the skin to take a measurement. If the indicator lamp is red, your skin is either too dark
or the skin tone cannot be detected.
8. If this is the case, press the trigger button again to repeat the measurement.
Note
If you want to cancel skin tone detection, press one of the energy level selection buttons (+ or -)
again to return to normal mode.
9. If skin tone detection was successful, check the result of the measurement by comparing it with the
skin and hair colour table.
10. If the value measured differs from the skin and hair colour table, you should always use the lower
energy level.
11. You can increase and decrease the energy level at any time by pressing the + and - buttons.
If you notice slight or no irritation during and after the first hair removal treatment while using the rec-
ommended energy level, you may increase the energy level by 1 in subsequent treatments.
WARNING
Do not increase the energy level if you experience an abnormal amount of pain during or after the
treatment using the beurer SalonPro System! (See “Step 6 Familiarise yourself with the possible side-
effects”)
Do not increase the energy level during the hair removal session, even if you do not notice any dis-
comfort.
Irritation can occur some time after the treatment itself.
STEP 6: Familiarise yourself with the possible side-effects of using the beurer SalonPro System
If the beurer SalonPro System is used in accordance with these instructions for use, side effects and
complications seldom occur in relation to the use of the beurer SalonPro System. However, every cos-
metic treatment method – including methods such as these designed for use at home – is associated
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beurer IPL 10000 plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beurer IPL 10000 plus in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 9,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info