752356
6
Zoom out
Zoom in
Previous page
1/92
Next page
Pedestal Fixing
The pool heater must be vertically fixed on ground or a certain pedestal made of wood or concrete before it can be used.
There should be two holes, 8mm in diameter on the pedestal, the space between which should be 254mm. Put the pool
heater on the pedestal and fix them together with bolts and nuts. The pedestal should weigh over 18kgs in order to
prevent the pool heater from accidentally falling.
254 MM
8 MM
Problem Cause
Troubleshooting
Solution
A. Power failure.
A. The Pool Heater is not working
.
B. Heating time is too long
.
C. Filter pump or Sand Filter does not match the Pool
Heater appropriately or Filter Pump or Sand Filter
failed, resulting in high or low water flow rates.
D. Pool Heater set-up failed
.
E. The thermal cut out cut off
.
F. Pool Heater failed
.
A. Hose Clamps are loose
.
B. Hose O-ring not in correct position
.
C. Hose Broken
.
A. Filter Pump or Sand Filter does not work
.
B. Filter Pump or Sand Filter broken
.
A. The light is broken.
A. Check power source.
A. Check the LED light to see whether the heater is working.
B. Highly recommend the use of a Bestway pool cover.
C. Replace the Filter Pump or Sand Filter following the
specification of this owner’s manual, and perform
maintenance according to the instructions of Filter Pump or
Sand Filter.
D. Reset-up the Pool Heater according to the instructions.
E. Press the “Reset” button on the Pool Heater.
F. Contact after-sales service.
A. Tighten the hose clamps
.
B. Check whether O-Ring are damaged.
C. Hose needs to be replaced
.
A. Reset-up the Filter Pump or Sand Filter according to the
instructions.
B.
Check and repair the Filter Pump or Sand Filter according to
the relevant instructions in the Filter Pump or Sand Filter’s
owner’s manual.
A. The heating light is wrong and the heater still works.
1. The heating light does not work.
2. Pool Heater not heating properly.
3. Inlet and Outlet Valves leak.
4. Water does not flow.
5.
The heating light turns off but the Pool
Heater heats.
Assembly
1. Set-up and fill the pool with water to the required level according to the
pool’s owner’s manual.
2. Attach the Filter Pump or Sand Filter’s Inlet Valve to the Pool:
a) Place the loose Hose Clamps on both ends of a Filter Pump or Sand
Filter Hose.
b) Attach the hose to Filter Pump or Sand Filter’s Inlet Valve and the
Pool’s Outlet Valve B.
c) Tighten the Hose Clamps.
3. Connect the Filter Pump or Sand Filter to the Pool Heater:
a) Place the loose Hose Clamps on both ends of the Pool Heater Hose.
b) Attach the hose to the Filter Pump or Sand Filter’s Outlet Valve and
the Pool Heater’s ‘INLET’ Valve and tighten the Hose Clamps.
4. Attach the Pool Heater to the Pool’s Inlet Valve A.
5. Loosen the Hose Clamps on the Pool’s Inlet and Outlet Valves; replace
the Stopper Plugs with Debris Screens. Water now flows to the Filter
Pump or Sand Filter and the Pool Heater. With the Hoses and the
Debris Screens in position, tighten the Hose Clamps.
6. Check that every port and valve is connected correctly.
6
POOL HEATER EQUIPOTENTIAL BONDING TERMINAL
It is recommended to arrange for a qualified electrician to connect the
Pool Heater to a equipotential bonding terminal using a (minimum)
2.5mm2 solid copper conductor.
NOTE: Drawings for illustration purpose only. May not
reflect actual product. Not to scale.
1. Insert the plug.
2. Press the “RESET” button, the indicator light turns green.
3. Press the “TEST” button, the indicator light turns off.
4. Press the “RESET” button, the indicator light turns green.
WARNING: The PRCD plug must be tested before each
use to avoid risk of electric shock.
WARNING: Before inserting plug into a power outlet, make
sure the current rate of the power outlet is suitable for the
pump.
WARNING: Do not use the heater if this test fails and
contact our After Sales Service.
PRCD Test
RESET
TEST
24
RESET
TEST
RESET
TEST
3
1
RESET
TEST
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bestway 58259 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bestway 58259 in the language / languages: All languages as an attachment in your email.

The manual is 19,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bestway 58259

Bestway 58259 User Manual - English - 6 pages

Bestway 58259 User Manual - Dutch, French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info