752356

Bestway 58259 Manual

4
Zoom out
Zoom in
Previous page
1/6
Next page
RESET
P6124
Hose
Clamp P6176
Hose
P6005 O-Ring
NOTE: To order spare parts for
the Pool Heater, please provide
us with part no. and part name.
Drawings for illustration
purposes only. May not reflect
actual product. Not to scale.
Assembly
1. Set-up and fill the pool with water to the required level according to the
pool’s owner’s manual.
2. Attach the Filter Pump or Sand Filter’s Inlet Valve to the Pool:
a) Place the loose Hose Clamps on both ends of a Filter Pump or Sand
Filter Hose.
b) Attach the hose to Filter Pump or Sand Filter’s Inlet Valve and the Pool’s
Outlet Valve.
c) Tighten the Hose Clamps.
3. Connect the Filter Pump or Sand Filter to the Pool Heater:
a) Place the loose Hose Clamps on both ends of the Pool Heater Hose.
b) Attach the hose to the Filter Pump or Sand Filter’s Outlet Valve and the
Pool Heater’s ‘INLET’ Valve and tighten the Hose Clamps.
4. Attach the Pool Heater to the Pool.
5. Loosen the Hose Clamps on the Pool’s Inlet and Outlet Valves; replace the
Stopper Plugs with Debris Screens. Water now flows to the Filter Pump or
Sand Filter and the Pool Heater. With the Hoses and the Debris Screens in
position, tighten the Hose Clamps.
6. Check that every port and valve is connected correctly.
Filter Pump
Above Ground Pool
Water Level
Sand Filter
P6124
P6124
Pedestal Fixing
The pool heater must be vertically fixed on ground or a certain pedestal made of wood or concrete before it can be used. There
should be two holes, 8mm in diameter on the pedestal, the space between which should be 254mm. Put the pool heater on the
pedestal and fix them together with bolts and nuts. The pedestal should weigh over 18kgs in order to prevent the pool heater from
accidentally falling.
Operation
1. Check the pool for correct installation and make sure both the pool’s Inlet
and Outlet Valves are fully covered by water before operating the Filter
Pump or Sand Filter of the Pool Heater. Make sure that the Pool Heater
and Filter Pump or Sand Filter are correctly connected.
2. Start the Filter Pump or Sand Filter according to the owner’s manual.
3. With the pump operating, insert the plug of Pool Heater into a socket.
4. Press the “-/O” button of the Pool Heater, the LED light turns on.
5. Press the “TEST” button, the LED light turns off.
6. Press the “-/O” button, and the Pool Heater is ready to use.
NOTE: The Pool Heater must be tested before each use.
NOTE: Never plug in the Pool Heater until the Filter Pump or Sand Filter has
been plugged in.
NOTE: To prevent the risk of electrical shock, ensure your hands are
completely dry when plugging-in the Filter Pump or Sand Filter and the
Pool Heater.
NOTE: To prevent the risk of electrical shock, never run the Filter Pump or
Sand Filter and the Pool Heater when people are in the pool.
NOTE: Do not dry run the Pool Heater. Damage caused by dry running the
Pool Heater is not covered by the manufacturer’s warranty.
7. Remember to disconnect the Pool Heater first. Never unplug the Filter
Pump or Sand Filter when the Pool Heater is running.
8. Unplug the Filter Pump or Sand Filter and enjoy warm pool water!
Maintenance
CAUTION: YOU MUST UNPLUG THE POOL HEATER FIRST,
THEN UNPLUG THE FILTER PUMP OR SAND FILTER BEFORE
PREFORMING MAINTENANCE OR SEVERE RISK OF INJURY OR
DEATH EXISTS.
1. Stop Water Flowing to the Filter Pump or Sand Filter and the Pool Heater:
a) Disconnect the Pool Heater and THEN the Filter Pump or Sand Filter .
b) Loosen the Hose Clamps on the pool’s Inlet and Outlet Hoses.
c) Replace the Debris Screens with the Stopper Plugs in the pool’s Inlet
and Outlet Valves.
d) Refer to the Filter Pump or Sand Filter ’s Owner’s Manual for information
on Filter Pump or Sand Filter maintenance.
2. After Filter Pump or Sand Filter maintenance, replace the Stopper Plugs
with the Debris Screens in the pool’s Inlet and Outlet Valves. Water will now
flow to the Filter Pump or Sand Filter and the Pool Heater.
3. Operate as outlined in the Operation section of this manual.
Storage and Winterization
CAUTION: YOU MUST UNPLUG THE POOL HEATER AND THE
FILTER PUMP OR SAND FILTER BEFORE MAINTENANCE
BEGINS OR SEVERE RISK OF INJURY OR DEATH EXISTS.
To avoid damage, pool equipment must be winterized when temperatures
decrease. Allowing water to freeze will damage the Pool Heater and void the
warranty.
The heater shall not be left out in the open air for long periods of time. When it
is not in used, please store it in a cool, dry place once it has been cleaned
and dried.
1. Follow the instructions previously outline to stop water flowing to the Filter
Pump or Sand Filter and the Pool Heater.
2. Detach all hoses.
3. Drain any water in the Pool Heater and clean all components thoroughly.
4. Put the Pool Heater in a cool, dry place, out of children’s reach.
Heating Reset
1. Be sure to press the "Reset" button on the
pool heater using a small and thin object before
initial operation
2. If the pool heater is not heating properly, press the "Reset"
button on the pool heater.
254 MM
8 MM
B
A
S-S-001462
4
S-S-001462/14.0x21.0cm (#58259GB 英规加热器说明书D版) JS-YF-2012-B-01266/英
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bestway 58259 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bestway 58259 in the language / languages: English as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bestway 58259

Bestway 58259 User Manual - Dutch, French - 13 pages

Bestway 58259 User Manual - All languages - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info