680440

Berner C500 Manual

32
Zoom out
Zoom in
Previous page
1/144
Next page
WARNING
Danger of crushing and shearing
Fingers or limbs may be crushed and severed if caught in
the toothed track or between the gate and closing edge
while the gate is in motion.
▶
Whenever the gate is moving, never touch the toothed
track, toothed wheel, and the main or secondary
closing edges.
4.1 Preparation
▶
Before initial start-up, check that all the connecting leads
are correctly installed at the connecting terminals.
▶
Make sure that all DIL switches are set to the factory
setting (OFF) (see Figure7), the gate is half open and the
operator engaged.
Change the following DIL switches:
▶
DIL switch1: Installation direction (see Figure7.1)
– To ON, if the gate closes towards the right.
– To OFF, if the gate closes towards the left.
▶
DIL switches3-7: Safety devices
(seeFigures9.6 / 9.7 / 9.8)
– Set according to the connected safety and protective
devices (see section 5.3 – 5.5). These are, however,
not active during set-up mode.
4.2 Teaching in the gate's end-of-travel positions
4.2.1 Recording the CLOSE end-of-travel position
▶
See Figure8.1a
The limit switch (reed contact) must be connected before
teaching in the end-of-travel positions. The limit switch wires
must be connected at the REED terminal.
The option relay has the same function as the red LED during
set-up. The limit switch position can be viewed from afar with
a connected lamp (seeFigure6.4).
Teaching in the CLOSE end-of-travel position:
1. Open the gate halfway.
2. Set DIL switch2 (set-up mode) to ON.
The green LED slowly flashes, the red LED remains lit.
3. Press circuit board button T and keep it pressed.
The gate now travels in CLOSE direction at slow speed.
The gate stops once the limit switch has been reached.
4. Immediately release circuit board buttonT.
The red LED goes out.
The gate is now in the CLOSE end of travel position.
NOTE:
If the gate travels in the opening direction, DIL switch1 is in
the wrong position and must be reset. Then repeat steps 1to4.
If the position of the gate does not correspond to the desired
CLOSE position, a readjustment must be made.
Readjusting the CLOSE end-of-travel position:
1. Adjust the position of the magnet by moving the magnet
slide.
2. Press circuit board buttonT until the gate reaches the
readjusted end-of-travel position and the red LED goes
out.
3. Repeat steps 1 + 2 until the desired end-of-travel
position has been reached.
4.2.2 Recording the OPEN end-of-travel position
▶
See Figure8.1b
Teaching in the OPEN end-of-travel position:
4. Press circuit board button T and keep it pressed.
The gate now travels in OPEN direction at slow speed.
5. Release circuit board buttonT, once the desired OPEN
end-of-travel position is reached.
6. Press circuit board button P to confirm this position.
The green LED flashes rapidly for 2seconds to indicate
that the OPEN end-of-travel position has been recorded
and then goes out.
4.2.3 Recording the partial opening end-of-travel
position
▶
See Figure8.1c
NOTE:
If press-and-hold operation has been set, it is not possible to
record the partial opening end-of-travel position.
Teaching in the partial opening end-of-travel position:
1. Press circuit board buttonT and keep it pressed to move
the gate back towards the CLOSE position.
The green LED will flash slowly.
2. Release circuit board button T once the desired partial
opening end-of-travel position is reached.
3. Press circuit board button P to confirm this position.
The green LED flashes rapidly for 2seconds to indicate
that the partial opening end-of-travel position has been
recorded and then goes out.
4.2.4 Ending the set-up-mode
▶
After you have finished the teach-in procedure, set
DILswitch2 back to OFF.
The green LED signals that forces must be taught in by
flashing quickly.
The safety equipment is active again.
4.2.5 Reference run
▶
See Figure8.2
After teaching in the end-of-travel positions, the first cycle is
always a reference run. During this reference run the option
relay clocks and a connected warning lamp flashes.
Reference run to CLOSE end-of-travel position:
▶
Press circuit board buttonT once.
The operator automatically moves into the CLOSE
end-of-travel position.
▶
If press-and-hold operation has been set (DIL switch16
to ON), press and hold circuit board buttonT until the
gate is in the close end-of-travel position.
NOTE:
Initial start-up is now finished if press-and-hold operation has
been set (DIL switch16 to ON).
4.3 Learning the forces
Once the end-of-travel positions have been taught in and the
reference run performed, force learning runs must also be
performed. For this, three successive gate cycles must take
place, during which none of the safety devices may be
activated. Recording the forces takes place automatically by
press-and-release operation in both directions and the option
relay clocks. The green LED flashes throughout. This LED is
steadily illuminated once the force learning runs have been
completed (see Figure9.1).
32
C300 - C800 / Rev. 1.1 RE / 07.2014
ENGLISH
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Berner C500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Berner C500 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 12,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info