Manual Berkel BSPS (page 28 of 38) (English)

673675

Zoom out

Zoom in

1/38

UM - CODE N4 N5 N6 N10 - REV 0.3

Cleaning the blade

WARNING: Use protective gloves and

concentrate on the job at hand.

RISK OF INJURY!

1. Press a damp cloth on the surface of

the blade and move it slowly from the

center to the edge, as shown in the

picture, on the side of the blade cover and

on the other side;

2. Dry in the same way using a dry cloth.

Cleaning the safety ring

Pass a damp cloth between the blade and

the safety ring.

Cleaning the machine body

1. Clean the machine body with a damp

cloth or a sponge rinsing frequently with

hot water;

2. Dry carefully.

NOTE: If you have a knife removing tool

then refer to section 6.2.4

Cleaning the sharpener

1. Clean the body with a damp cloth and

the grindstones with a semi-rigid nylon

brush;

2. Don’t immerse sharpener.

Cleaning the components in the base

The components contained in the base

do not need any special cleaning;

occasionally remove the dust that can

accumulate in the end area of the

carriage and of the thickness plate

regulation.

6.2.4. Knife removing tool instructions

If your machine is supplied with a knife

remover please proceed as follows:

WARNING: Cutting danger! Act with

attention and concentrate on the job.

- Disconnect the machine from the

electric mains supply;

- Remove the blade cover unscrewing

completely (counterclockwise) the

tension rod knob (see 6.2.2)

- Ensure the slide deflector is removed

before fitting the knife remouver;

- Fit the knife remover (1) as in the

drawing and insert the external edge of

the ring with attention, under the ring

(2);

- Adjust the knife remover correctly (1)

and screw the knurled knobs

completely in to the threaded holes of

the knife (3);

- Loosen and remove the screws (4)

fixing the blade to the pulley shaft;

- Pull off the knife remover with the

blade always using the knurled knobs

(3);

- Proceed to an accurate cleaning of

the machine, as described in section

6.2.3, and of the rear of blade from

the centre outwards and allow to dry;

- Now you can place the blade still fitted

on the knife remover back on to the

slicer following the above procedure,

in reverse.

WARNING: after removing the knife

removing tool check each of the blade

fixing screws to make sure they are

tight.

6.2.5. Reassembling the slicing ma-

chine

Reassembling the sharpener

1. Make sure the locking knob is loose

(about 10 turns);

Insert the sharpener as shown in the

picture until it stops at its correct

position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Berkel BSPS in the language / languages: English as an attachment in your email.

The manual is 2,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Berkel BSPS Manual

Product: