711333

Beper VE112 Manual

11
Zoom out
Zoom in
Previous page
1/44
Next page
11
Stand Fan Use instructions
EN
Before cleaning, always unplug the appliance.
To protect against electric shock, do not immerse cord, plug or any
parts of the appliance into water or other uids.
Do not hold the appliance with wet hands or feet.
Do not hold the appliance with naked feet.
Do not expose the appliance to atmospheric agents such as rain,
wind, snow, hail.
Do not use the appliance near explosives, highly ammable mate-
rials, gases, burning ames, heaters.
Do not allow children, disabled people or every people without expe-
rience or technical ability to use the appliance if they are not properly
watched over. Close supervision is necessary when any appliance
used by or near children.
Make sure that children do not play with this appliance.
If you decide not to use the appliance any longer, make it unservice-
able by simply cutting the supply cable after disconnecting the plug
from the socket.
ALSO MAKE ANY DANGEROUS PARTS UNSERVICE-
ABLE, ESPECIALLY FOR CHILDREN WHO COULD
PLAY WITH THE APPLIANCE.
ASSEMBLY INSTRUCTIONS:
• Unscrew the L-shaped screw and remove it and the clamping washer from the end of the base
tube.
• Loosen the height adjustment ring at the top of the base tube and pull out the extension pole to
the desired height, or all the way to the top for maximum height (you may have to push it up from
the bottom if it is tight or stuck). At the desired height, turn the height adjustment ring clockwise to
tighten securely.
• Insert the base tube into the hole on the base, turn over the base and afx the tube using the L-
shaped screw and the clamping washer. Tighten the screw rmly but do not overtighten.
• Set the base on a level, dry surface.
• Lightly loosen the set screw, attach the fan body to the top of the extension pole. Push the body
down as far as possible and then tighten securely with the set screw.
• The motor shaft has the blade cap and guard nut attached. Remove the cap by turning it clockwise
and the nut by turning it anticlockwise.
• Place the rear guard on the front of the motor housing, lining up the two positioning knobs on the
front of the motor housing with the two holes in the rear guard. Make sure that the handle is up the
top. Push the guard in rmly until the three knobs protrude through the holes. Secure the rear guard
by reattaching the guard nut and turning it clockwise to tighten.
• If the motor shaft is covered with a protected sleeve, remove the sleeve.
Slide the blade onto the motor shaft, making sure to match the protrusions on the shaft with the
slots in the blade. Tighten the blade with the blade cap, turning it anticlockwise to tighten it securely.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beper VE112 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beper VE112 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info