711111

Beper RI503 Manual

18
Zoom out
Zoom in
Previous page
1/74
Next page
18
Electric replace Use instructions
8. Place the front glass panel over the front of the replace carefully aligning the hooks with the brackets on each
side of the glass panel (Fig. G)
Note: use at least two people to carry out this operation, to avoid the accidental fall and breakage of the
panel.
To rmly secure the glass panel, fasten the screws removed before on each side of the panel until com-
pletely tightened.
Operation and use
After completing installation and mounting operations, plug the appliance to the wall socket.
The appliance has a digital display that shows all the selected settings (Fig. H)
The appliance can be operated by the control panel (found on the top part of the appliance – Fig. I) or by the
remote control.
Turning on the appliance
After plugging the appliance to a wall socket, place the general switch found right below the control panel on “I”.
Press on the control panel or the remote control, the appliance will turn on and the LED ame will light up; it
is now possible to set and/or select the desired function.
To turn the appliance off, press again.
Day/time setting
Day/time setting can be made by the control panel, by pressing , or by the remote control, by pressing “DAY”,
“HOUR” and “MIN”.
To set the day
From control panel: press , display will show the LED indicator related to the selected day of the week (Sun”
– Sunday; “Mon” – Monday; “Tue” – Tuesday; “Wed” – Wednesday; “Thu” – Thursday; “Fri” – Friday; “Sat” – Sa-
turday). Press “+”/”-“ to select the present day of the week.
When the LED indicator related to the selected day stops blinking, the setting is conrmed
From remote control: press ”DAY”, display will show the LED indicator related to the selected day of the week
(see above). Press “+”/”-“ to select the present day of the week.
When the LED indicator related to the selected day stops blinking, the setting is conrmed
To set the time
From control panel: press twice, LED indicator related to the hour on the display will start blinking. Press “+”/”-“
to set the hour (from 00 to 23)
Press three times, LED indicator related to the minutes on the display will start blinking. Press “+”/”-“ to set
the minutes (from 00 to 59)
When the LED indicator related to the selected hour/minutes stops blinking, the setting is conrmed
From remote control: press “HOUR”, LED indicator related to the hour on the display will start blinking. Press
“+”/”-“ to set the hour (from 00 to 23)
Press “MIN”, LED indicator related to the minutes on the display will start blinking. Press “+”/”-“ to set the minutes
(from 00 to 59)
When the LED indicator related to the selected hour/minutes stops blinking, the setting is conrmed
Flame intensity adjustment
The intensity of the ame can be regulated from the control panel, or from the remote control, simply by pres-
sing until the desired level of intensity is selected.
5 levels of intensity are available, from the highest to the lowest.
Selection is shown on display.
Heating mode setting
Heating mode can be set both from control panel and remote control.
To set heating mode from control panel, press as follows:
Press once to select low heating mode
Press twice to select high heating mode
Press three times to turn heating off; the fan will keep operating for approx. 10 seconds before coming to a
complete stop
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beper RI503 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beper RI503 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info