577843
15
Zoom out
Zoom in
Previous page
1/17
Next page
03/ 2012
BENNING SUN 2
13
8.2.2 Starting / stopping the data logger
- Press the key
7
(LOG) for > 5 seconds to activate the data logger. Display: "LOG".
- Press the key
7
(LOG) again and then the key
7
(OK) to confirm "run". The measured
values are written into the internal memory including a time / date stamp. The digital display
2
goes out and the device switches over into the energy-saving stand-by mode.
- Press any key to display the progress of the data logger. The digital display briefly goes on
and then goes out again.
- If you want to stop the data logger, press any key to display the data logger. Press the key
7
(LOG) and then the key
7
(OK) to confirm "StOP".
- Press the key
3
or
4
to exit the data logger.
8.2.3 Reading out the data logger via the USB interface
- Install the driver and the download software from the CD-ROM once.
- Connect the BENNING SUN 2 to your PC by means of the USB connecting cable and switch
the device ON.
- Start the download program, go to "Tools" and click "Refresh Ports".
- Select the COM port used and click "Download".
- The download of measured values starts.
Troubleshooting:
- One of the most frequent connection errors is the selection of the wrong COM port.
- If the measured values are not downloaded, verify the COM port used by means of the
Device Manager of your system.
- As soon as the BENNING SUN 2 has been connected to your PC by means of the USB
connecting cable, the hardware driver and thus the COM port used can be viewed in the
Device Manager under "Ports (COM & LPT)", e.g. Silicon Labs CP210x USB to UART
Bridge (COM14).
8.2.4 Setting the date and the time
- Press the key
5
to display the time / date on the digital display
2
.
- Press the key
5
again for > 5 seconds until the hour display starts ashing.
- Press the ► key
3
to select the time / date eld (eld is ashing).
- Press the ▲ key
4
or ▼ key
5
to increase or decrease the value.
- Press the key
7
(OK) to store the setting.
time / 24-hour display
day / month
year
8.2.5 Changing the displayed unit
- Press the
3
key for > 5 seconds until the displayed temperature unit starts flashing.
- Press the ►
3
key to select the respective unit for insolation or temperature.
- Press the ▲
4
or
5
key to change between the units °C or °F or between the units W/m²
or BTU/hr/ft².
- Press the
7
key (OK) to store the setting.
9. Maintenance
Do not open the device. It does not contain any components requiring maintenance by the user.
Repair and service must be carried out by qualied personnel only!
9.1 Cleaning
Clean the exterior of the device with a clean dry cloth (exception: special cleaning wipers). Do not
use any solvents or abrasives to clean the device. Make sure that the battery compartment and
the battery contacts are not contaminated by leaking battery electrolyte.
If there are electrolyte contamination or white deposits in the area of the battery or the battery
housing, clean these areas as well by means of a dry cloth.
9.2 Battery replacement
The BENNING SUN 2 is supplied by means of two 1.5 V batteries of type AA (IEC LR6).
It is necessary to replace the batteries as soon as the battery voltage falls below 1.8 V (see
section 8.1.2).
Proceed as follows to replace the battery:
- Switch the BENNING SUN 2 off.
- Put the BENNING SUN 2 face down and slide the battery compartment cover off the bottom
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning SUN 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning SUN 2 in the language / languages: English, German as an attachment in your email.

The manual is 2,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Benning SUN 2

Benning SUN 2 Quick start guide - English, German, Dutch, French, Italian, Spanish - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info