577368
9
Zoom out
Zoom in
Previous page
1/58
Next page
08/ 2012 9 / 58
BENNING ST 750 A
6. General Information / Technical Specifications
The BENNING ST 750 A Appliance Tester is provided with a touchscreen and a switchable test
socket.Thebuilt-inUSBinterfaceandthe"BENNINGPC-WinST750"PCsoftwareallowread-out
of the memory data as well as communication between PC and tester. The BENNING ST 750 A is
intended to be used for safety tests of electrical appliances after
- repair, modification and periodic inspection of electrical appliances (DIN VDE 0701-0702)
- periodic tests and after repair of medical electrical devices or systems (DIN EN 62353; VDE
0751-1; IEC 62353).
The DIN VDE 0701-0702 standard applies to tests regarding the electrical safety of electrical ap-
pliances with rated voltages of 1000 V AC / 1500 V DC. The standard shall apply together with the
test procedures and tests to be applied for proving the electrical safety by observing the admissible
limitingvalues.Thisstandardshallalsoapplytotestsafterrepair,modicationandperiodictests
ofelectricalapplianceswhichare rmlyconnectedtotheelectricalsystemorwhichareportable
devices.Theresponsible qualied electrician shalldecidewhetheranelectricalappliance which
isrmlyconnectedtothesystemshallbetestedduringperiodictestingtogetherwiththesystem
according to DIN VDE 0105-100 (VDE 0105-100) or whether it shall be tested according to this stan-
dard, but separate from the system or together with a part of the system. Electrical appliances which
arenormallyconnectedbymeansofaplugconnection,butexceptionallyarermlyconnected,shall
be tested according to DIN VDE 0701-0702. For testing a system, it shall be allowed to disconnect
the connected devices and to test them separately according to DIN VDE 0701-0702. The standard
shallnotapplytodevicesforwhichspeciclaws,provisions,operatingmanualsorregulationshave
to be observed ( e.g. explosion hazard areas, mining etc.). Test samples with three-phase connec-
tion shall be tested by means of a corresponding adapter and a separate leakage current clamp.
The measuring results shall be entered manually into the appliance tester for joint logging. The tests
shall be carriedoutby competent persons,qualied electricians orbyelectrotechnically trained
personnelundersupervisionofqualiedelectricians.
Fortestswiththewarning"Highleakagecurrent!",thetestingmustbecarriedoutby
qualiedelectriciansonly!
Thenecessityandtimeintervalsofperiodictestsaredenede.g.intheGermanaccidentprevention
regulationBGVA3(BGVA2(VBG4))"Electricalsystemsandequipment"andintheGermanHealth
andSafetyatWorkRegulation("BetrSichV").
§ 5 of BGV A3 (BGV A2 (VBG 4)) says:
1. The company shall ensure that electrical systems and equipment are tested with regard to
their proper condition:
- before initial commissioning and after modification or repair, before recommissioning
by a qualified electrician or under supervision of a qualified electrician, in defined time
intervals.
- The intervals shall be determined in such a way that assumable occurring defects can be
detected in good time.
2. For testing, the corresponding electrotechnical rules shall be observed. On request of the
professional association, a test book with certain entries shall be kept.
7. Commissioning / Setup
Important system settings (expert settings) can only be made by trained service
specialists by entering a password!
Remove SD memory cards only with the appliance tester being switched off!
Before switching the device on, remove all test cables from the appliance tester
and reconnect them only after having carried out a self-test.
For commissioning:
- Connect the mains connection cable to
the shock-proof socket (230 V, 50 Hz,
16 A).
-Setthemainsswitchtoposition"I".
- The Appliance Tester carries out a self-
testandafterrun-upshowsthermware
version in the upper line of the display.
- After run-up, press the <Setup> button.
7.1 Battery-operated user interface
The BENNING ST 750 A Appliance Tester is equipped with an integrated storage battery for main-
taining the function of the user interface in case of a mains power failure. Thus, for a short time, the
device can be carried from one place of inspection to another without requiring mains voltage and
without being switched off before. Moreover, it is still possible to access the SD card to open or edit
databases. It is not possible to carry out electrical tests in battery operating mode.
When the device is operated without mains voltage, the following information is shown on the dis-
play depending on the battery charge condition:
Assoonas"Batterywarninglevel2"isshownonthedisplay,immediatelyconnectthedevicetothe
mains voltage in order to charge the storage battery. The storage battery will be charged automati-
cally in mains operating mode with the device being switched on.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning ST 750A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning ST 750A in the language / languages: English as an attachment in your email.

The manual is 7,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Benning ST 750A

Benning ST 750A User Manual - German - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info