577333
16
Zoom out
Zoom in
Previous page
1/120
Next page
09/ 2013
BENNING MM 4
10
2. Safety notes
The instrument is built and tested in accordance with
DIN VDE 0411 part 1/ EN 61010-1
and has left the factory in perfectly safe technical condition.
To maintain this condition and ensure safe operation of the multimeter, the user
must observe the notes and warnings given in these instructions at all times.
The unit may be used only in power circuits within the over-
voltage category II with a conductor for 600 V max. to earth,
or within overvoltage category III with a conductor for 300 V
against ground.
Remember that work on electrical components of all kinds is
dangerous. Even low voltages of 30 V AC and 60 V DC may be
dangerous to human life.
Before starting the multimeter up, always check it as well as all
cables and wires for signs of damage.
Should it appear that safe operation of the multimeter is no longer possible, it
should be shut down immediately and secured to prevent it being switched on
accidentally.
It may be assumed that safe operation is no longer possible:
- if the instrument or the measuring leads show visible signs of damage, or
- if the multimeter no longer functions, or
- after long periods of storage under unfavourable conditions, or
- after being subjected to rough transport.
In order to avoid danger,
- do not touch the bare prod tips of the measuring leads,
- insert the measurement leads in the appropriately desig-
nated measuring sockets on the multimeter
3. Scope of supply
The following items make up the standard BENNING MM 4 package:
3.1 one Multimeter,
3.2 one current transducer clamp,
3.3 one safety test lead, black (length = 1.4 m, tip Ø 4 mm) with safety
caps,
3.4 two test probes, red (tip Ø 4 mm),
3.5 one compact protection case,
3.6 two 1.5 V micro-batteries (in place in Multimeter on delivery),
3.7 the set Operating Instructions.
Note on consumable parts:
The BENNING MM 4 is supplied by two 1.5 V batteries (2 x 1,5-V-IEC LR 03).
4. Description of unit
The BENNING MM 4 consists of two functional units:
- the Multimeter and
- the current transducer clamp.
See fig.1: Front panel of unit
The operating and indicating elements shown in fig. 1 are as follows:
1 Housing
2 Sliding switch for selecting the desired functions.
- Aus (OFF)
- Measurement of alternating voltage (AC) and direct voltage (DC).
These functions alternate with one-another when the function button
with the blue marking is pressed. When pressed longer (2 sec.) meas-
urement of alternating current, etc. The digital display 3 indicates the
function currently in effect.
- Resistance measurement, continuity test with buzzer and diode
test. These functions alternate with one-another when the function
button with the blue marking is pressed. The digital display 3 indicates
the function currently in effect.
3 Digital display (liquid-crystal principle). The following are indicated:
- the measurement value with the max. indication 4200,
- the polarity indication,
- the decimal point,
- the symbol for discharged battery,
- the type of voltage selected (DC or AC voltage),
- the measurement value held (hold function),
- the deviation from a measurement value stored in the unit memory
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Benning MM 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Benning MM 4 in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 6,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info