661649
8
Zoom out
Zoom in
Previous page
1/13
Next page
Changing the radio key
If a neighbor also has a Visit system, you can change the radio key so that your systems don’t interfere.
The radio key is changed on the transmitters and must be set to the same positon on all units in the system.
Here is how you change the radio key
1 Open the transmitter cover and move any radio key switch/es to the up=on position
to change the radio key. See the transmitter user manual for further information.
2 Press and hold the function button on the pager until the green and yellow LEDs
blink alternately. Release the button.
3 Press the test button/s on the transmitter within 30 seconds to send the new radio key.
4 All Visit LEDs blink 5 times to show that the radio key has been changed. It then returns to normal mode.
1 2 3 4
x 5
105 Installers guide
On
O
Installers guide 106
Advanced programming
By using advanced programming, you can customize the signal pattern from a specic transmitter and event,
displaying the LED colour and vibration pattern of your choice. The advanced programming overrides the
radio key and pairs the units via the serial number. Please note that smoke alarms cannot be programmed for
safety reasons.
Note: The transmitter must be activated as it is intended to be used in the system to generate the right signal.
This means that you can’t always use the transmitter test button, see Default signal pattern for the relevant
transmitter.
Here is how you program the pager:
1 Press and hold the function button on the pager. The green and yellow Visit LEDs will start to blink
alternately. While still holding down the button, activate the desired transmitter as intended.
The yellow battery LED on the pager will light up to indicate that you are in advanced programming mode.
Release the button.
2 Scroll through the dierent Visit LED options by pressing the function button on the pager. Select the desired
Visit LED pattern by holding down the function button until the battery LED goes out and lights up again.
3 Scroll through the dierent vibration options by pressing the function button on the pager. Select the desired
vibration pattern by holding down the function button until the battery LED goes out and lights up again.
4 The pager will now show the new Visit LED colour and vibration pattern. Press the function button briey to
end the demonstration. After a short while, the pager will return to normal mode.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bellman BE1470 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bellman BE1470 in the language / languages: German as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bellman BE1470

Bellman BE1470 User Manual - English - 4 pages

Bellman BE1470 User Manual - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info