747160
11
Zoom out
Zoom in
Previous page
1/16
Next page
Advanced programming
Advanced programming provides additional options for those who wish to make special
modications to the Bellman Visit Flash Receiver.
The idea is that it should be possible to select a completely unique signal pattern which is
linked to activation from a specic input on a special Bellman Visit transmitter. The function
works regardless of the radio key settings on the units that are programmed. Please note that,
for safety reasons, the function does not work with the BE1480 Bellman Visit Smoke Alarm.
By using advanced programming of the Bellman Visit Flash Receiver, it can be adjusted so
that its signal pattern corresponds exactly to what is required. In other words an entirely indi-
vidual signal pattern can be programmed, such as displaying an orange permanently lit LED
and a constant vibration.
In order to adjust the setting, the Bellman Visit Transmitter to which the Bellman Visit Flash
Receiver should be adapted must be available. The transmitter must also be connected so
that it can be activated in the way in which it is intended to be used.
Proceed as follows:
1 Hold down the Test Button (9) on the Bellman Visit Flash Receiver until the green
and
yellow
LEDs blink alternately. The Bellman Visit Flash Receiver will now be in program-
ming mode for about 30 seconds.
2 Hold down the Test Button (9) at the same time as the relevant Bellman Visit transmitter
is activated in precisely the way in which it is intended to be used. Note that all inputs are
individual. It is therefore not possible to use the Test Button on a Bellman Visit Telephone
Transmitter whose telephone input will indicate the relevant pattern.
3 Scroll through the dierent LED options by a short press on the Test Button (9). Select the
relevant indication by holding down the Test Button (9) until the LED goes out and
starts to shine with a constant green light again.
4 Scroll through the dierent vibration options by a short press on the Test Button (9). Select
the relevant indication by holding down the Test Button (9) until the LED goes out and
starts to shine with a constant green light again.
5 The Bellman Visit Flash Receiver will now show the indication method programmed. End
the display with a short press of the Test Button (9).
6 After a short while, the Bellman Visit Flash Receiver will automatically return to normal
mode. This function is essential where a transmitter has to work in a special way with re-
gard to a specic receiver.
Resetting advanced programming
It is quite easy to reset the Bellman Visit Flash Receiver if it needs to be reset after it has been
programmed using advanced programming.
11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bellman BE1443 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bellman BE1443 in the language / languages: German as an attachment in your email.

The manual is 2,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info