Manual Bell Super Shell (page 3 of 8) (English, French, Spanish)

772317

Zoom out

Zoom in

1/8

1ATTACH MOUNT ONTO BIKE FRAME

1. Remove four (4) screws from back of

mount using 5mm Allen wrench.

2. Place front of mount around seat

tube of bike. Insert back of mount

to front of mount, insert screws.

Do not fully tighten. Do not place

around brake and derailleur cable

and housing.

CLICK RACK INTO MOUNT

1. Slide the ends of the carrier rack into the top holes on the mount.

Once secured, you will hear a click. This means the carrier rack is

secured to the mount.

2. Slide the loose mount up or down until there is about 6”

between rear wheel and bottom of carrier. Be sure mount is

centered along rear wheel facing forward.

3. Tighten the screws on the mount until mount will not slip

up, down, or side to side.

4. Tighten fasteners securely, and check them frequently.

CARRIER RACK ATTACHMENT

1. Insert carrier rack bars simultaneously into bicycle mount. You should hear a

“click” when properly secured.

CHILD CARRIER ATTACHMENT

1. Untwist the clamp on the bottom of the child carrier by

turning the knob.

2. Place carrier clamp over the carrier rack, hook one

side of the clamp around the edge, then push the

other side of clamp down over carrier rack and turn

knob to tighten the clamp around the carrier rack.

The knob has a security feature so that it does

not loosen accidentally. To tighten or loosen

the clamp, pull the knob handle out, and

at the same time, turn to tighten or

loosen accordingly.

3. Loop security strap webbing

around seat post.

CHILD CARRIER REMOVAL

1. Unclip the security strap.

2. Pull knob out and twist until carrier

clamp loosens the seat.

EASY, 3-STEP INSTALLATION

WARNING

Do not modify child carrier or bicycle. If carrier rack will not t on your bicycle, consult your local bicycle dealer or call our Customer Service

1.800.456.BELL for assistance. Failure to properly attach clamp onto the carrier rack could result in the child carrier falling off the carrier rack.

WARNING

Hearing a clicking sound does not mean the knob is tight. You must pull knob

out and twist until secure.

STANDARD BIKE RACK MOUNTING

SEAT PAD INSTALLATION

OSCILLATING GRAB BAR

FOOT REST INSTALLATION

FOOT STRAP ATTACHMENT

CHILD CARRIER ADJUSTMENT

SEATING YOUR CHILD

The Super Shell can be secured to and removed from most

standard bicycle racks by following the steps in the Seat

Attachment and Seat Removal sections. The mount and carrier

rack included do not need to be installed for this conguration.

Place seat pad into bottom of child carrier. Thread retention

harness through seat pad. Insert all four seat pad plugs into the

bottom of the child carrier.

While riding, the grab bar can be used in either the forward or

back locking positions. Push both round buttons on each side

of bars to pivot front or back until it clicks into place.

To insert foot rest, insert top hook into preferred height. Slide

bottom tab into slot and pinch both together at the same time

while pushing the foot rest into place. Pull at them gently to

ensure they are secured properly. To remove foot rest, pinch

the hook and tab at the same time and pull up, freeing the

bottom tab. Then pull the top hook free.

1. Loop one piece of Velcro® through each foot rest and attach

back onto itself.

2. Insert top hooks of foot rests into opening along leg. Must be

at least three notches from bottom. Push to lower tabs

through respective opening and click into place. Lower hook

tabs need to be lifted slightly when inserted into slot.

Child carrier should be positioned as far forward as practical.

WITH ONE PERSON HOLDING THE BICYCLE STEADY, THE

SECOND PERSON PLACES CHILD IN CHILD CARRIER.

Adjust harness to child’s height. If child’s shoulders are at or

below the lower strap slot holes, move the harness to the lower

holes. Push the plastic washer that hold the ends of the harness

out through the holes. Fasten buckles accordingly.

WARNING

Positioning the child carrier too far back will increase the risk of

loss of steering and/or braking control.

A standard bicycle rack must have a load rating of 40 pounds

or greater to be used with the child carrier. Failure to properly

attach clamp onto the carrier rack could result in seat falling off

the carrier rack.

4 | English 5 | English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bell Super Shell in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 2.78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bell Super Shell Manual

Product: