648619

Bell phones Big Button Plus 20270 Manual

16
Zoom out
Zoom in
Previous page
1/18
Next page
15 010508A-1
CALLER ID UNIT TROUBLESHOOTING TABLE
SYMPTOM SOLUTION
The Caller ID
LCD panel is
blank
•
Check the batteries for proper installation.
• If the batteries are weak or dead, replace with new batteries
(alkaline batteries are recommended). Please refer to the
“Battery Installation” section of the user’s manual for more
details.
• Check the connection of the AC adaptor.
The Caller ID
LCD panel does
not show the
caller’s name
and/or phone
number
• The Caller ID unit will not function until you have Caller ID
service provided by your local phone company. Call your
local phone company to have Caller ID installed on your
telephone line.
•
Check your telephone line connections. Refer to the section
“INSTALLATION” of the manual for details.
• If you picked up the phone before
the second ring, the caller
information will not
be correctly received. If you have a
telephone answering device (TAD) connected with the unit, set
the TAD to answer after two rings or more.
•
If it is a blocked call or an out-of-area call, the caller’s name
and/or phone number will not appear on the display. Please
refer to the “Receiving Caller ID Information” section of the
user’s manual for more details.
•
If only the caller’s phone number appears on the display, it
may
be a Single Data Message Format (SDMF) call, as opposed to a
Multiple Data Message Format (MDMF) call. Please refer to
the Glossary section of the user’s manual for definitions.
“LINE
ERROR”
• On rare occasions, the Caller ID information sent by the
telephone company may have an error in the transmission.
This is not the fault of your Caller ID unit. It can only capture
and store the data that was received.
Cannot delete
call records in
memory
• The DELETE button must be pressed twice briefly to delete a
single call record. To delete all call records, press and hold the
DELETE button for as least 5 seconds. Please refer to the
“ERASING A CALL/ALL CALLS” section of the manual for
more details.
No Data Sent
•
On rare occasions, Caller ID information sent by the telephone
company may be too weak to be detected by the Caller ID.
This is not the fault of the Caller ID unit; it can only capture
and store the digital data that was received.
• This message also appears when the Caller’s local phone
company does not have Caller ID service available.
TELEPHONE UNIT TROUBLESHOOTING TABLE
… 16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bell phones Big Button Plus 20270 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bell phones Big Button Plus 20270 in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info