556825
10
Zoom out
Zoom in
Previous page
1/40
Next page
10
EN
Do not make connections via extension
cables or multi-plugs.
B
Damaged power cables must be
replaced by the Authorized Service
Agents.
Electrical requirements
Before you insert the plug into the wall socket
make sure that the voltage and the frequency
shown in the rating label corresponds to your
electricity supply.
We recommend that this appliance be
connected to the mains supply via a suitable
switched and fused socket in a readily
accessible position.
Should the mains lead of the appliance
become damaged or need replacing at any
time, it must be replaced by a special purpose
made mains lead which can only be obtained
from a Authorised Service Agent.
B
This appliance must be earthed
If the fitted moulded plug is not suitable for
your socket, then the plug should be cut off
and an appropriate plug fitted.
Destroy the old plug, which is cut off as a
plug with a bared cord could cause a shock
hazard if inserted into a socket elsewhere in
the house.
The moulded plug on this appliance
incorporates a 13A fuse. Should the fuse
need to be replaced an ASTA approved
BS1362 fuse of the same rating must be
used. Do not forget to refit the fuse cover.
In the event of losing the fuse cover, the
plug must not be used until a replacement
fuse cover has been fitted. Colour of the
replacement fuse cover must be the same
colour as that visible on the pin face of the
plug. Fuse covers are available from any good
electrical store.
Important
Fitting a different plug
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals on
your plug, proceed as follows:
1 Connect the green - yellow or green
(earth) wire to the terminal in the plug
marked ‘E or with the symbol f or
coloured green and yellow or green.
2 Connect the blue (neutral) wire to the
terminal in the plug marked N’ or
coloured black.
3 Connect the brown (live) wire to the
terminal in the plug marked Lor
coloured red.
With the alternative plugs a 13A fuse must be fitted
either in the plug or adaptor or in the main fuse
box. If in doubt contact a qualified electrician.
First use
Before starting to use the product, make sure
that all preparations are made in accordance
with the instructions in sections "Important
safety instructions" and "Installation".
To prepare the product for washing laundry,
perform first operation in Drum Cleaning
programme. If your machine is not featured
with Drum Cleaning programme, use
Cottons-90 programme and select Additional
Water or Extra Rinse auxiliary functions as
well. Before starting the programme, put max.
100 g of powder anti-limescale into the main
wash detergent compartment (compartment
nr. II). If the anti-limescale is in tablet form, put
only one tablet into compartment nr. II. Dry the
inside of the bellow with a clean piece of cloth
after the programme has come to an end.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WMB71642 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WMB71642 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info