556825

BEKO WMB71642 Manual

8
Zoom out
Zoom in
Previous page
1/40
Next page
8
EN
C
Keep the transportation safety bolts in
a safe place to reuse when the washing
machine needs to be moved again in the
future.
C
Never move the product without the
transportation safety bolts properly fixed
in place!
Connecting water supply
C
The water supply pressure required to run
the product is between 1 to 10 bars (0.1
– 10 MPa). It is necessary to have 10 – 80
liters of water flowing from the fully open
tap in one minute to have your machine
run smoothly. Attach a pressure reducing
valve if water pressure is higher.
C
If you are going to use the double water-
inlet product as a single (cold) water-inlet
unit, you must install the supplied stopper
to the hot water valve before operating
the product. (Applies for the products
supplied with a blind stopper group.)
C
If you want to use both water inlets of the
product, connect the hot water hose after
removing the stopper and gasket group
from the hot water valve. (Applies for the
products supplied with a blind stopper
group.)
A
Models with a single water inlet should
not be connected to the hot water tap. In
such a case the laundry will get damaged
or the product will switch to protection
mode and will not operate.
A
Do not use old or used water inlet hoses
on the new product. It may cause stains
on your laundry.
1. Connect the special hoses supplied with
the product to the water inlets on the
product. Red hose (left) (max. 90 ºC) is for
hot water inlet, blue hose (right) (max. 25
ºC) is for cold water inlet.
A
Ensure that the cold and hot water
connections are made correctly when
installing the product. Otherwise, your
laundry will come out hot at the end of
the washing process and wear out.
2. Tighten all hose nuts by hand. Never use
a wrench when tightening the nuts.
3. Open the taps completely after making
the hose connection to check for water
leaks at the connection points. If any
leaks occur, turn off the tap and remove
the nut. Retighten the nut carefully after
checking the seal. To prevent water
leakages and damages caused by them,
keep the taps closed when the machine
is not in use.
Connecting to the drain
• The end of the drain hose must be
directly connected to the wastewater
drain or to the washbasin.
A
Your house will be flooded if the
hose comes out of its housing during
water discharge. Moreover, there is
risk of scalding due to high washing
temperatures! To prevent such situations
and to ensure smooth water intake and
discharge of the machine, fix the end
of the discharge hose tightly so that it
cannot come out.
• The hose should be attached to a height
of at least 40 cm, and 100 cm at most.
• In case the hose is elevated after
laying it on the floor level or close to
the ground (less than 40 cm above the
ground), water discharge becomes more
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO WMB71642 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO WMB71642 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info