Manual BEKO HCA61531X (page 31 of 88) (All languages)

676962

Zoom out

Zoom in

1/88

- 29 -

•Commandsmechanical(Fig.18) the key symbols are ex-

plained below:

= LIGHT

= OFF

= SPEED I

D = SPEED II

E = SPEED III.

•Mechanicalcontrols(Fig.19)the symbols are as follows:

A = LIGHT/ON-OFF key

B = OFF/FIRST SPEED key

C = SECOND SPEED key

D = THIRD SPEED key.

If the hood is shut off at first, second or third speed, when

it is turned back on, it will start at the same speed it was in

when switched off.

•Commands(Fig.20):

A = Light Key Turn on/off lights.

B = ON/OFF Key Turn on/off the hood.

The equipment switches on at the 1st speed.

To turn off the hood press key B.

C = Display Indicates the speed of the selected motor and

activation of the timer.

D = Key Increases and decreases the speed of the motor with

a cyclical pattern, 1°-2°- 3° ... 1°-2°- 3° speed.

By pressing the key for 3 seconds the INTENSE function comes

into operation for 6 minutes, on the C display the number 4

starts flashing.

At the end of the minutes the engine will start operating at

the previously set speed.

To deactivate the intense speed, before the set time, press

the B key and the hood turns off, but not if the lights are on.

E = Timer key With any speed entered (excluding Intense

speed) by pressing the key the timer function is activated for

15 min. At the end of the count the hood turns off (motor and

any lights that are on).

To turn off the Timer function, before the pre-set time, press

the B key and the hood turns off, or by pressing the timer key

again it turns off but the hood continues to operate.

•SaturationActivecarbon/Anti-greasefilters:

- After 30 h of operation, with the hood ON on display C , the

letter F starts to flash which means that the anti-grease filters

have to be washed.

Once the clean filter is replaced you must reset the electronic

memory, with the hood off press key B and D for 5 sec. until

the display C shows the letter F fixed for 2 sec.

-After 120 h of operation, with the hood ON on display C the

letter C starts to flash which means that the carbon filters

have to be washed or replaced.

Once the clean filter is replaced you must do a double re-set so

with the hood off press key B and D for 5 sec. until the display

C shows the letter F fixed for 2 sec.

Repeat and press key B and D for 5 sec. until display C shows

the letter C fixed for 2 sec. .

•Commands

(Fig.21)

A = ON/OFF key

Turns the hood on/off.

By pressing key A the LED flashes for 2 sec. then remains fixed

and the equipment starts in 1° speed.

To turn the hood off press key A again, the LED flashes for 2

sec. then it turns off.

B = FIRST SPEED KEY

C = SECOND SPEED Key/TIMER function

- Key C also activates the TIMER function.

- The key flashes for the full duration of the TIMER.

- With any speed entered (excluding Intense speed where

applicable) by pressing C for about 3 seconds the TIMER

function is activated for 15 min. At the end of the count the

hood turns off (motor and any lights that are on).

- To deactivate the Timer function, before the pre-set time,

press any key except the F key for ON/OFF Lights.

D = THIRD SPEED key/ INTENSE SPEED Function

- Key D also activates the INTENSE SPEED function.

- The key flashes for the full duration of the INTENSE SPEED

function.

- By pressing the key for 3 seconds the INTENSE function comes

on for 6 minutes.

- At the end of the minutes the engine will start operating at

the previously set speed.

To deactivate the intense speed, before the pre-set time, press

any key except the F key for ON/OFF Lights.

Attention! Some models only work up to the 3rd speed and,

therefore, do not have the intense function.

E = ON/OFF LIGHTS key

•SaturationActivecarbon/Anti-greasefilters:

- When the hood is on the LED corresponding to the A and B

keys flash, the anti-grease filters must be washed.

Once the clean filter is put back the electronic memory must

be reset, with the hood off press A for 5 sec. , the reset is

confirmed by a flashing of the LED A and B.

- When the hood is on the LED corresponding to C and E flash,

the carbon filters must be washed.

Once the clean filter is put back the electronic memory must

be reset, with the hood off press A for 5 sec. , the reset is

confirmed by a flashing of the LED C and E.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY

FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE

ABOVE WARNINGS.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of BEKO HCA61531X in the language / languages: All languages as an attachment in your email.

The manual is 5,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

BEKO HCA61531X Manual

Product: