676962

BEKO HCA61531X Manual

29
Zoom out
Zoom in
Previous page
1/88
Next page
- 27 -
ductor used to circulate hot air or for evacuating fumes from
other appliances generated by other than an electrical source.
Before proceeding with the assembly operations, remove the
anti-grease filter(s) (Fig.2.2 - Fig.3.2) so that the unit is easier to
handle.
- In the case of assembly of the appliance in the suction version
prepare the hole for evacuation of the air.
• If the appliance is supplied with the small cupola M remove
it by releasing it as indicated in Fig.2.3 - Fig.3.3.
Before proceeding with the assembly operations, for easier
manoeuvrability of the appliance disengage the anti-grease
lter by pulling handle B as indicated in Fig.2.2 - Fig.3.2.
If one owns a model with perimeter suction panel, before
carrying out this operation, perform the following phases:
- Open panel C as indicated in Fig.2.1 - Fig.3.1.
- If one owns the version with three A panels release them from
the xing pins by pulling outwards (Fig.3.4) and then remove
them from safety pins N (Fig.3.4) placed inside the hood. To
put them back perform the operation in reverse order.
ATTENTION! During this disassembly and assembly
operation ensure to hold the panel securely to prevent
accidental falls.
• Wall mounting:
Trace the bottom side of the hood on the wall. Consider the
measurements shown in Fig.4A and minimum distance from
the cooking surface (Fig.4B).
- Position the xing template on the wall, making sure that the
line coincides with the line previously made on the wall.
- Mark the xing holes and cut them into the material (Fig.5).
- Fix the 2 top screws K and screw anchors (Fig.5), without
tightening them completely.
- Place the appliance against the wall, align it in horizontal
position and tighten screws K (Fig.6A).
- Once the adjustment has been completed, x the hood using
the 2 screws C (Fig.6B).
- When carrying out the xing operations, use only screws
and screw anchors suited to the type of wall (e.g. reinforced
concrete, plasterboard etc.).
- If the screws and screw anchors are supplied with the
appliance, make sure that they are suited to the type of wall
to which the hood must be xed.
•Installationofmodelswithoutdecorativeducts:
Extractorhood
- Unclip the canopy M and remove the grille E (Fig.7).
- Pass the power supply cable through the slot in the canopy
M, as indicated in Fig.9A.1.
- Taking the grommet H, position it between the power cable
and the slot (Fig.9A.2).
- Connect the exible hose L (not supplied) to the hood (Fig.9B).
- Re-position the small cupola M paying attention that it is
hitched perfectly to the xing pins G (Fig.9B).
• Filtering version:
- Unclip the canopy M and remove the grille E (Fig.7).
- Pass the power supply cable through the slot in the canopy
M, as indicated in Fig.8.1.
- Taking the grommet H, position it between the power cable
and the slot (Fig.8.2).
- Fix the small cupola M and the grille E making sure that is it
perfectly hooked on to the fastening pins G (Fig.8).
• Optional accessories:
This model may have decorative ducts as optional accessories
- ask your retailer for information.
Before installing decorative ues it is necessary to remove
the small cupola M and loosen the 4 screws Q that lock the
fastening pins G as shown in Fig.11.
•Installationofmodelswithdecorativeducts:
Extractorhood
Make sure the electrical power supply is within the measure-
ments of the decorative connector. Adjust the width of the
support bracket of the top connector (Fig.10.2). Then x it
to the ceiling so that it is on the same axis as the hood using
screws A and observing the distance from the ceiling shown in
Fig.10.1. Connect ange F to the air exhaust hole using exible
hose L (Fig.12A). Slide the top connector inside the lower duct
and place this on the body (Fig.12B). Pull out the top duct as
far as the bracket and secure it using screws B (Fig.10.2). To
transform the hood from a ducting version into a ltering
version, ask your dealer for the charcoal lters and follow the
installation instructions.
•Filterhood:
Please note:
The lters must be ordered from your dealer as an accessory.
- To transform the hood from the SUCTION version to the
FILTERING version, charcoal lters must be ordered from your
dealer as an accessory. Two types of kit are available, one with
non-renewable lters (Fig.13) and the other with renewable
lters (washable) (Fig.14). Unlike traditional carbon lters,
this carbon lter can be washed and reactivated for approxi-
mately 12-15 times. With normal hood use, this lter should
be cleaned once every 2-3 months. The lter can be washed
into a dishwasher at the highest temperature using a standard
dishwasher detergent. After washing, dry the lter in the oven
at 100°C for 10-15 minutes to reactivate it. The lter will retain
its odour-absorbing capacity for three years, after which it will
have to be replaced.
- If a bracket is found in the packaging like that indicated in
Fig.14 loosen the screws already installed inside the hood and
install the bracket using the previously-removed screws.
- To replace re-usable carbon filters Y, remove the brackets
from their seat, pulling them outwards (Fig.14).
- If your product is not supplied with the bracket, it means that
the active charcoal lter cannot be renewed (Fig.13). These
must be applied to the suction unit inside the hood, centring
them in it and turning them 90° until they snap into place
(Fig.13).
USE AND MAINTENANCE
• We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance is
left running for 15 minutes after the food is cooked, in order
to thoroughly eliminate all contaminated air.
The effective performance of the cooker hood depends on
constant maintenance; the anti-grease filter and the active
carbon filter both require special attention.
•Theanti-greasefilter is responsible retaining the grease
particles suspended in the air, therefore it is subject to clogging
with variable frequency according to the use of the appliance.
- To prevent the danger of possible fires, at least every 2
months one must wash the anti-grease filters by hand using
non-abrasive neutral liquid detergents or in the dishwasher
at low temperatures and on short cycles.
- After a few washes, colour alterations may occur. This does
not give the right to claim their replacement.
•Theactivecarbonfilters are used to purify the air that is
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BEKO HCA61531X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BEKO HCA61531X in the language / languages: All languages as an attachment in your email.

The manual is 5,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info