660520

Behringer Xenyx XL1600 Manual

12
Zoom out
Zoom in
Previous page
1/22
Next page
12 XENYX XL3200/XL2400/XL1600 User Manual
CLIP
The CLIP LED lights up as soon as the channel's level is too high. In this case,
reduce the channel's input amplication with the TRIM control.
SIG
The SIG LED lights up when a channel's signal is higher than -20 dB. The LED is
not aected by the fader. The signals are indicated even when the fader is pulled
down and the channel is muted.
Fader
The channel fader adjusts the level of the channel signal as part of the main mix
(or submix).
1-2, 3-4, MIX
The routing switch routes the signal to the respective subgroup or the main mix
or both. The XENYX features 4 subgroups. The PAN control determines the group
to which the signal is routed (fully left: Sub 1 or 3, fully right: Sub 2 or 4).
5.2 Stereo channels
+48 V
This control LED lights up when the phantom power is activated. The switch is
located on the rear panel of the unit.
MIC TRIM
The MIC TRIM control adjusts amplication of the microphone input.
Theamplication ranges between 0 and +60 dB.
◊ Be sure to set this control fully counter-clockwise before you connect or
disconnect a signal source to or from one of the inputs.
80 Hz
Press the 80 Hz switch to activate the high-pass lter which blends out
low-frequency noise (-3 dB at 80 Hz, 18 dB/octave).
LINE TRIM
The LINE TRIM control adjusts the amplication of the LINE input,
rangingbetween -20 and +20 dB. When centered (at 12 o'clock),
thelinesignalisneither boosted nor cut.
5.2.1 Equalizer stereo channels
The stereo channels provide 4-band equalization. Each frequency band can be
boosted and cut up to 15 dB and has a at response when the controls are in
center position.
HIGH
The HIGH control of the EQ section adjusts the high-frequency range of the
respective channel. This is a shelving lter which boosts and cuts the frequencies
above 12 kHz.
HIGH MID
The HIGH MID control adjusts the mid frequency range. Thisisapeak lter which
boosts and cuts the frequencies centered at3 kHz.
LOW MID
The LOW MID control adjusts the mid frequency range. Thisisapeak lter which
boosts and cuts the frequencies centered at 300Hz.
LOW
The LOW control adjusts the low-frequency range. This is a shelving lter which
boosts and cuts the frequencies below 80 Hz.
EQ
The EQ push-button switch activates the equalizer. Toggle the EQ to give you a
quick comparison between unprocessed and processed signal.
5.2.2 Stereo channel FX/MON/AUX send paths
The aux and FX paths of the stereo channels work in principle the same way as
the mono channels. Since the aux buses are mono, the stereo signal needs to be
converted to a mono signal before being routed to these buses.
5.2.3 Channel fader, pan control, mute switch, etc.
BAL(ANCE)
The BAL(ANCE) control has the same function as the PAN control on the mono
channels. It determines the relative volume of the left and right input signals
before they are routed to the stereo main mix bus (or to two subgroups).
MUTE
Use the MUTE switch to mute the channel signal. The MUTE LED is illuminated
when the channel is muted
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx XL1600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx XL1600 in the language / languages: English as an attachment in your email.

The manual is 6,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx XL1600

Behringer Xenyx XL1600 Quick start guide - English, German - 18 pages

Behringer Xenyx XL1600 User Manual - German - 21 pages

Behringer Xenyx XL1600 User Manual - Dutch - 21 pages

Behringer Xenyx XL1600 Quick start guide - French, Portuguese, Spanish - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info