660520
13
Zoom out
Zoom in
Previous page
1/22
Next page
13 XENYX XL3200/XL2400/XL1600 User Manual
SOLO
Press the SOLO switch to hear the signal on your headphones and simultaneously
see it on the monitor display ½). The corresponding LED lights up when the solo
function is activated.
CLIP
The CLIP LED lights up as soon as the channel's level is too high. In this case, turnthe
TRIM control to reduce the channel's input amplication until the LED goes out.
SIG
The SIG LED lights up when a channel's signal is higher than -20 dB. The LED is
not aected by the fader. The signals are indicated even when the fader is pulled
down and the channel is muted.
Fader
The channel fader governs the level of the channel signal as part of the main
mix(or submix)
1-2, 3-4, MAIN
The routing switch feeds the signal to the respective subgroup or the main mix
or both. Please note that when using the routing switch to route a stereo signal
to the subgroups the balance control needs to be centered so that the signal is
routed to two groups and remains in stereo.
5.3 Main section
5.3.1 MAIN A section
BAL(ANCE)
The BAL(ANCE) control adjusts the mix of the left and right output signal before
both signals are routed to the MAIN A output. This way the left and right volume
level of the mixer sumcan individually be adjusted if necessary.
MAIN MUTE
When the MAIN MUTE switch is pressed, all input channels are muted. The MUTE
LED lights up when the MUTE switch is pressed. Only the CD/TAPE signal will be
routed to the main mix. In this way, you can prevent the microphones from picking
up unwanted sounds or noise that would interfere with CD playback during a break.
The main mix and channel faders can remain in their normal positions while playing
back music from CD (usingthe CD/TAPE inputs, so you don’t lose your mix.
MAIN A
Use this high-precision MAIN fader to control the output level of the main mix.
MAIN B
Depending on the settings of the MAIN B section, the level of the Main B output is
aected by the MAIN A fader.
5.4 Level meters
Four high-resolution LED meters indicate the levels of the monitor buses' and
mixer sum's output signals. As soon as you have pressed the solo switch on the
mixing console, the monitor LED meter automatically shows the solo signal.
Themaster signal is alwaysindicated.
1 MON 2
The monitor meters indicate the levels of the monitor buses 1 and 2. In solo mode
(SOLO LED lights up) thePFL signal (mono, only left meter) or the AFL signal
(stereo, left and right meter) are shown. Thisdepends on the state of the PFL and
AFL switch inthe solosection.
SOLO
When a SOLO switch is pressed on the mixing console, not only the corresponding
LED lights up, but also the global SOLO LED. This way you can keep a cool head
when mixing live and don't have to check the whole console to see that one
SOLOswitch is active. Simultaneously this LED indicates that the monitor meters
are in solo mode.
MAIN
The high-precision level meter accurately indicates the output signal
level(MAINOUT A).
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx XL1600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx XL1600 in the language / languages: English as an attachment in your email.

The manual is 6,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx XL1600

Behringer Xenyx XL1600 Quick start guide - English, German - 18 pages

Behringer Xenyx XL1600 User Manual - German - 21 pages

Behringer Xenyx XL1600 User Manual - Dutch - 21 pages

Behringer Xenyx XL1600 Quick start guide - French, Portuguese, Spanish - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info