542754

Behringer Xenyx X1832USB Manual

13
Zoom out
Zoom in
Previous page
1/19
Next page
13 XENYX X2442USB/X2222USB/X1832USB/X1622USB User Manual
FBQ FEEDBACK DETECTION
The switch turns on the FBQ Feedback Detection System. It uses the LEDs in the
frequency band faders to indicate the critical frequencies. On a per-need basis,
lower the frequency range in question somewhat in order to avoid feedback.
Thegraphic stereo equalizer has to be turned on in order to use this function.
◊ Logically, at least one (ideally several) microphone channels have to be
open for feedback to occur at all!
Feedback is particularly common when stage monitors (“wedges”) are
concerned, because monitors project sound in the direction of microphones.
Therefore, you can also use the FBQ Feedback Detection for monitors by placing
the equalizer in the monitor bus (see MAIN MIX/MONITOR).
4. Digital Eects Processor
24-BIT MULTI-EFFECTS PROCESSOR
Here you can nd a list of all presets stored in the multi-eects processor.
Thisbuilt-in eects module produces high-grade standard eects such as reverb,
chorus, anger, delay and various combination eects. Use the Aux Send FX on
the channels and the Aux Send FX master control to determine the input signal of
the eects processor.
X1832USB
Fig. 4.1: Digital eects module
The built-in stereo eects processor has the advantage that it does not need to
be wired up. This excludes the danger of humming or level mismatch right from
the start and thus considerably facilitates use.
These eect presets are classical “mixing eects”. If you move the STEREO AUX
RETURN FX control, you mix the channel signal (dry) and the eect signal. Youcan
control the balance between the two signals with the channel fader and the
STEREO AUX RETURN FX control.
FX OUT
Mixing consoles X2222USB and X2442USB have a separate output for the eects
device, which is unbalanced and stereo (tip = left signal; ring = right signal;
sleeve = ground/shielding). Thus, you can record, for example, a vocal track
enhanced with reverb in parallel to a “dry” vocal track; when doing the mix-down
later on, you can freely determine the amount of reverb added.
◊ The X2442USB has the effect output on the rear, X2222USB has it
located next to the aux sends on the front panel.
FX FOOTSW.
Connect a standard foot switch to the foot switch jack and use this to switch
the eects processor on and o. A light at the bottom of the display indicates
wheater the eects processor has been muted by the foot switch.
◊ In Chapter 6.2 you will find an illustration showing how to connect your
foot switch correctly.
LEVEL
The LED level meter on the eects module should display a suciently high
level. Take care to ensure that the clip LED only lights up at peak levels. If it is
lit constantly, you are overloading the eects processor and this could cause
unpleasant distortion.
PROGRAM
You can select the eect preset by turning the PROGRAM control. The display
ashes with the number of the current preset. To recall the selected preset,
presson the button; the ashing stops. You can also recall the selected preset
with the foot switch.
5. Rear Panel Connectors
5.1 Main mix outputs, insert points and control
room outputs
X2442USB
Fig. 5.1: Main Mix outputs, main mix insert points and control room outputs
MAIN OUTPUTS
The MAIN outputs carry the MAIN MIX signal and are on balanced XLR jacks with
a nominal level of +4 dBu. In parallel with this, ¼" phone jacks carry the main
mix signal in a balanced format (X1622USB: here, the phone jack outputs are
unbalanced and located on the front panel).
CONTROL ROOM OUTPUTS (CTRL OUT)
The control room output is normally connected to the monitoring system in the
control room and carries the stereo mix or, when selected, the solo signals.
MAIN INS(ERTS) (X2442USB only)
These are the insert points for the main mix. In the signal path, they are
post-main mix amp, but pre-main fader(s). Use them to insert, for example,
adynamics processor or graphic equalizer. Please also note the information on
insert points in chapter 5.3.
5.2 Subgroup outputs
Fig. 5.2: Subgroup outputs
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx X1832USB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx X1832USB in the language / languages: English as an attachment in your email.

The manual is 5,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx X1832USB

Behringer Xenyx X1832USB Quick start guide - German, Dutch, Italian, Polish, Portuguese, Swedish - 37 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info