542754
15
Zoom out
Zoom in
Previous page
1/19
Next page
15 XENYX X2442USB/X2222USB/X1832USB/X1622USB User Manual
SERIAL NUMBER
Please note the important information on the serial number given in
chapter1.3.3.
6. Installation
6.1 Rack mounting
The packaging of your mixing console contains two 19" rack mounts for
installation on the side panels of the console.
Before you can attach the rack mounts to the mixing console, you need to remove
the screws holding the left and right side panels. Then, use these screws to
fasten the two rack mounts, each specically to one side. With the rack mounts
installed, you can mount the mixing console in a commercially available 19" rack.
Be sure to allow for proper air ow around the unit, and do not place the mixing
console close to radiators or power amps, so as to avoid overheating.
Only use the screws holding the mixing console side panels to fasten
the 19" rack mounts.
6.2 Cable connections
You will need a large number of cables for the various connections of the console.
The illustrations below show the wiring of these cables. Be sure to use only high-
grade cables.
strain relief clamp
sleeve
tip
sleeve
pole 1/ground
tip
pole 2
The footswitch connects both poles momentarily
¼" TS footswitch connector
Fig. 6.1: Foot switch connector
6.2.1 Audio connections
Please use commercial RCA cables to wire the 2-track inputs and outputs.
You can, of course, also connect unbalanced devices to the balanced input/
outputs. Use either mono plugs, or use stereo plugs to link the ring and shaft (or
pins 1 & 3 in the case of XLR connectors).
output
For unbalanced use, pin 1 and pin 3
have to be bridged
1 = ground/shield
2 = hot (+ve)
3 = cold (-ve)
input
12
3
1
2
3
Balanced use with XLR connectors
Fig. 6.2: XLR connections
Caution! You must never use unbalanced XLR connectors (PIN 1 and
3 connected) at the MIC input jacks if you want to use the phantom
power supply.
strain relief clamp
sleeve
tip
sleeve
(ground/shield)
Unbalanced ¼" TS connector
tip
(signal)
Fig. 6.3: ¼" mono plug
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.
Balanced ¼" TRS connector
ring
cold (-ve)
tip
hot (+ve)
Fig. 6.4: ¼" stereo plug
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx X1832USB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx X1832USB in the language / languages: English as an attachment in your email.

The manual is 5,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx X1832USB

Behringer Xenyx X1832USB Quick start guide - German, Dutch, Italian, Polish, Portuguese, Swedish - 37 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info