660465
8
Zoom out
Zoom in
Previous page
1/12
Next page
8 XENYX 1002B User Manual
4.2 Creating a monitor mix
For live applications, audio engineers often send dierent mixes to the audience
and to the performing musicians. To allow this, the 1002B is equipped with a
dedicated monitor send bus. Each channel features a MON knob that sends a
“pre-fader” signal to the MON OUT jack, allowing the channel’s volume fader to
be adjusted without aecting the monitor mix. The signal can also be used as a
second eects send. Follow these steps to set up a basic monitor mix:
• Make sure the powered monitor speaker or power amp is turned o.
Connect a ¼" TS cable from the MON OUT jack to the powered speaker or
power amp
• Turn on the powered speaker or power amp, and then turn the volume up
about half way
• Turn the MON SEND knob to the center (12 o’clock) position. This setting may
need to be adjusted later depending on volume requirements
• As the musicians begin to play, turn each channel’s MON knob up slowly until
each source is audible in the monitor mix
• It may take some time to get a balanced mix that all the musicians are
happy with. If possible, avoid turning a channel’s MON knob much past the
center position. Do not point the monitor speakers directly at a microphone,
as this will likely cause feedback
See the Applications section for details.
As previously stated, the MON SEND jack can also be used as a second eects
send. This application requires a similar setup to the normal eects send, but
since the signal from each channel is sent pre-fader using the MON knob, signal.
Therefore, if you alter a channels volume during the performance, you must also
adjust that channel’s MON knob.
• NOTE: When using the MON SEND for eects, if you neglect to change a
channels MON knob while turning that channel’s volume fader all the
way down, you will still hear the eected signal coming through the mix.
This problem happens because the signal routes “pre-fader,” but the normal
FX SEND bus will not experience this issue
4.3 Battery installation
The 1002B can be powered by three 9V batteries. This feature allows you, for
example, to capture a high-quality recording while sitting on the beach with
your laptop. You’re no longer tethered by an electrical outlet. You can still record
with condenser mics thanks to the 18V of phantom power supplied by two of
the batteries. Follow these steps to install the batteries:
• Open the battery compartment located on the underside of the mixer.
You will need to remove a small screw with a Phillips screwdriver
• Slide the compartment cover out. There are slots for three batteries inside
the compartment
• Insert the batteries so that the + and – poles are in the correct position
• Replace the cover and tighten the screw
The battery power will last approximately four hours using high-quality
alkaline batteries.
5. Applications
Fig. 5.1: Field Recording
Fig. 5.2: Live Small Combo
UCA222
XENYX1002B
HPS5000
UL2000M
XENYX1002B
DI100
HPS5000
B212D
F1220A
MP3 Player
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer Xenyx 1002B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer Xenyx 1002B in the language / languages: English as an attachment in your email.

The manual is 2,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer Xenyx 1002B

Behringer Xenyx 1002B Quick start guide - English, German - 13 pages

Behringer Xenyx 1002B User Manual - German - 12 pages

Behringer Xenyx 1002B Quick start guide - French, Portuguese, Spanish - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info