Manual Behringer X32 Compact (page 45 of 74) (English)

660491

Zoom out

Zoom in

1/74

45 X32 COMPACT DIGITAL MIXER User Manual

• Linear: In this mode, the rate of gain change is constant (as set by the

timing controls). Therefore, the greater the signal dynamic excursion,

the longer the compressor will take to complete a gain change.

Also,since the total time that the compressor spends in attack or decay

is proportional to the size of the gain excursion, the harmonic content

of the compression artifacts will seem to reduce in frequency content.

The louder the signal excursion is. This type of compressor is useful

for generating dynamic sound eects because the sonic character of

the compression is much more aected by time control settings and

program material than the exponential type.

9. Adjust the 5th encoder to set the release time of the compressor.

10. Tap the 5th encoder to engage the “auto” function, which automatically

optimizes advanced parameters such as attack, hold and release.

11. Adjust the 6th encoder to set the makeup gain of the compressor,

usefulwhen the compression eect has reduced the overall signal level of

the channel too much.

Page 2

1. The 1st encoder still engages and adjusts the threshold.

2. Adjust the 2nd encoder to set the mix of the compressor. Normally this

would be set to 100%, but by reducing the mix level, an eect called

‘parallel compression’ can be achieved, allowing some of the signal to pass

through uncompressed.

3. Adjust the 3rd encoder to set the steepness of the compressor “knee”

between ve separate settings. Adjust this control to switch between a

“harder” sounding or more transparent compression eect.

4. Tap the 3rd encoder to move the compressor eect before or after the

equalizer in the channel signal path.

5. Adjust the 4th encoder to set the frequency of the key lter that can be used

to trigger the compressor.

6. Tap the 4th encoder to toggle the key lter on/o, allowing a specic

frequency to control the compressor.

7. Adjust the 5th encoder to set the steepness of the EQ slope used in

thecompressor.

8. Tap the 5th encoder to send the key source to the solo bus, allowing the key

source to be monitored and evaluated.

9. Adjust the 6th encoder to select the specic key source to be used.

Choicesinclude “self” (the channel’s own signal) as well as any other

input/output of the console.

10. Tap the 6th encoder to assign the selected key source to the compressor.

7.2. 5 Home Screen: EQ Tab

The EQ tab displays all aspects of the channel equalizer and also displays a

detailed visual graph of the current EQ curve. This tab can also be accessed

directly by pressing the “View” button in the top panel Equalizer section.

1. If the currently selected channel is an input, the channel equalizer contains

four bands, with various aspects of each band adjusted by encoders 2-5.

2. If the currently selected channel is a bus, the channel equalizer contains six

bands, with various aspects of each band adjusted by encoders 1-6.

3. On the EQ screen, the various push encoders are always tied to an aspect of

the frequency adjustment, and the Up/Down navigation controls are used

to toggle between the 4 bands. The 6th encoder also toggles which band

is active.

• Adjust the 1st encoder to set the low cut frequency.

• Tap the 1st encoder to engage the low cut.

• Adjust the 2nd encoder to adjust the frequency for the selected band.

All 4 bands can be shifted between 20 Hz and 20 kHz, so the band

labeled 'Low' can actually be used to adjust mids, etc.

• Tap the 2nd encoder to determine whether the RTA operates as a bar

graph or spectrograph.

• Adjust the 3rd encoder to set the amount of cut or boost for the

selected band.

• Tap the 3rd encoder to set the RTA as pre or post, depending if you want

to monitor the incoming signal or the eects of the EQ adjustment.

• Adjust the 4th encoder to set the bandwidth (Q) of the selected band.

This is only available if the band is set to PEQ or VEQ.

• Tap the 4th encoder to reset the selected EQ band.

• Adjust the 5th encoder to determine the mode of the selected band.

The following options are available:

• Low cut

• Low shelf

• PEQ (standard parametric)

• VEQ (vintage style)

• High shelf

• High cut

• Tap the 5th encoder to reset all of the EQ bands.

• Adjust the 6th encoder to select the frequency band.

• Tap the 6th encoder to activate the EQ.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Behringer X32 Compact in the language / languages: English as an attachment in your email.

The manual is 15,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer X32 Compact

Behringer X32 Compact Quick start guide - English, German, French, Portuguese, Spanish - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Behringer X32 Compact Manual

Product: