660561

Behringer VT250FX Manual

5
Zoom out
Zoom in
Previous page
1/13
Next page
5 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
(13) With the MIDDLE control (VT100FXH and VT100FX only) you can raise or
lower the midrange frequencies on the OVERDRIVE channel.
(14) The TREBLE control adjusts the treble frequencies on the OVERDRIVE channel.
(15) Use the CONTOUR control for additional, highly characteristic adjustment
of the midrange, allowing you to easily create traditional as well
as ultra-modern guitar sounds.
(16) The VOLUME control adjusts the volume level of the OVERDRIVE channel.
2.1.3 DIGITAL FX
(17) The DIGITAL FX LED lights up when the eects processor is active.
(18) Use the FX PRESET control to select one of 16 eects.
Preset FX
1 - 4 Chorus/Delay
5 - 8 Delay
9 - 12 Chorus
13 - 16 Flanger
Tab. 2.1: Eects
(19) The FX LEVEL control adjusts the mix ratio between the original and
the eect signal.
(20) The REVERB LEVEL control determines the eect intensity of the
additional reverb eect.
(21) The FX LOOP MIX control (VT100FXH and VT100FX only) determines
the eect intensity of the external eect (see Chapter 2.2.1 FX LOOP).
2.1.4 MASTER section
(22) The MASTER VOLUME control adjusts both the overall volume and
the line out/headphones volume.
(23) The VTC push button activates and deactivates the VTC Virtual Tube Circuitry.
(24) The CD IN connector allows you to connect the output signal of a CD player,
tape deck, or CD/MD walkman. For example, you can play back music CDs or
CDs accompanying a guitar tutor while practising. This connector can also
be used as a LINE OUT output. In this case, the guitar signal is output with no
speaker simulation applied and can be routed to an external amp or mixing
console. This will not mute the VIRTUBE’s built-in loudspeaker.
(25) The LINE OUT/PHONES jack is for headphones connection. Internal speaker
simulation is applied to the headphones signal in order to produce an
authentic signal. The VIRTUBE’s built-in loudspeaker is muted when this
connector is used.
◊ The headphones output signal can also be routed to a mixing console or
other sound reinforcement system. To do so, connect the headphones
output with the line input on the mixing console. Use a standard cable
with 1/4" TS connectors. If hum problems occur, you could insert a
DI box, e.g. BEHRINGER ULTRA-DI DI100 or DI120.
◊ Some headphones tend to produce distortion with too high
volume level. Please turn down the volume a bit, until distortion stops.
(26) The POWER switch turns your VIRTUBE on and o. It should always be in the
OFF position when connecting the unit to the mains.
◊ Please note: Merely switching the unit off does not mean that it is fully
disconnected from the mains. To disconnect the unit from the mains,
pull out the mains connector. Before installation, please make sure
that the mains connector has not been damaged. If you do not use the
unit for an extended period of time, please disconnect it at the mains.
2.2 Rear panel
(27) The VIRTUBE is connected to the mains using a standard IEC receptacle.
A suitable power cord is included with the unit.
(28) FUSE HOLDER/VOLTAGE SELECTOR. Before connecting the unit to
the mains, ensure that the voltage setting matches your local voltage.
Blown fuses must be replaced with a fuse of the same type and rating.
On some units, the fuse holder can be switched to one of two positions,
i.e. 230 V and 120 V. Please note: when operating the unit outside Europe at
120 V, a higher fuse rating is required (see Chapter 4, “Installation”).
(29) This is where the fan of the unit is located.
(30) The SPEAKER OUT connectors (only one on the VT100FX and VT50FX)
can be used to connect external speakers with a miminum impedance of
4 Ω. The outputs of the VT250FX deliver 50 Watts of power per channel
(L/R). Always use speakers with a minimum impedance of 8 Ω to ensure
maximum power output. Using the SPEAKER OUT connectors will mute the
built-in loudspeakers.
2.2.1 FX LOOP
(31) The FX LEVEL button allows you to adapt the FX LOOP to the operating level
of an external eects device (+4 dBu/-10 dBV).
(32) The VIRTUBE provides a serial insert path for inserting external eects
(e.g. reverb processor). To do so, connect the FX SEND jack to the input of the
eects device.
◊ The FX SEND can also be used as a parallel output with no effects,
for example, to record a “dry” guitar signal. As long as the RETURN jack
is not in use, there will be no break in the internal signal path.
(28)
(27) (29)
(30) (35)
(33) (31) (32) (34)
Fig. 2.2: VIRTUBE control elements (rear panel)
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer VT250FX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer VT250FX in the language / languages: English as an attachment in your email.

The manual is 6,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer VT250FX

Behringer VT250FX User Manual - German - 13 pages

Behringer VT250FX User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info