660561
3
Zoom out
Zoom in
Previous page
1/13
Next page
User Manual
VIRTUBE
VT250
2 x 50-Watt Guitar Amplier with 2 Independent Channels,
VTC Tube Modeling, Dual FX and 2 Original BUGERA 12" Speakers
VT100 /VT50
100/60-Watt Guitar Amplier with 2 Independent Channels,
VTC Tube Modeling, Dual FX and Original BUGERA 12" Speaker
VT100 H
100-Watt Guitar Amplier Head with 2 Independent Channels,
VTC Tube Modeling and Dual FX
2 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
Thank you
Congratulations! With the VIRTUBE, you have the newest generation of
guitar amps. It oers an extremely broad range of options and possibilities,
theonly limit being your own creativity. The VIRTUBE is an allrounder with so
many features that you hardly need any other equipment.
Table of Contents
Thank you .......................................................................2
Important Safety Instructions ...................................... 3
Legal Disclaimer ............................................................. 3
Limited warranty ............................................................ 3
1. Introduction ............................................................... 4
1.1 Before you get started ...................................................... 4
1.1.1 Online registration ........................................................ 4
2. Control Elements ....................................................... 4
2.1 Front panel ............................................................................ 4
2.1.1 CLEAN CHANNEL ........................................................... 4
2.1.2 OVERDRIVE CHANNEL ................................................. 4
2.1.3 DIGITAL FX ....................................................................... 5
2.1.4 MASTER section ............................................................. 5
2.2 Rear panel ............................................................................. 5
2.2.1 FX LOOP ........................................................................... 5
3. Application Examples ............................................... 6
3.1 Set-up for practicing with playbacks ........................... 6
3.2 Recording set-up with eects device.......................... 6
3.3 Live set-up with external speaker box ........................ 7
3.4 Wiring the VT100FXH ........................................................ 7
4. Installation ................................................................. 8
5. Specications ............................................................ 9
3 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
Important Safety
Instructions
LEGAL DISCLAIMER
LIMITED WARRANTY
Terminals marked with this symbol carry
electrical current of su cient magnitude
to constitute risk of electric shock.
Use only high-quality professional speaker cables with
¼" TS or twist-locking plugs pre-installed. Allother
installation or modi cation should be performed only
by quali edpersonnel.
This symbol, wherever it appears,
alertsyou to the presence of uninsulated
dangerous voltage inside the
enclosure-voltage that may be su cient to constitute a
risk ofshock.
This symbol, wherever it appears,
alertsyou to important operating and
maintenance instructions in the
accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, donot
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
quali ed personnel.
Caution
To reduce the risk of  re or electric shock,
do not expose this appliance to rain and
moisture. The apparatus shall not be exposed to dripping
or splashing liquids and no objects  lled with liquids,
suchas vases, shall be placed on the apparatus.
Caution
These service instructions are for use
by quali ed service personnel only.
Toreduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by quali ed
servicepersonnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampli ers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. Ifthe
provided plug does not  t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Use only attachments/accessories speci ed by
themanufacturer.
12. Use only with the
cart, stand, tripod, bracket,
or table speci ed by the
manufacturer, orsold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to quali ed service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
beendropped.
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.
TECHNICAL SPECIFICATIONS AND APPEARANCES
ARE SUBJECT TO CHANGE WITHOUT NOTICE AND
ACCURACY IS NOT GUARANTEED. BEHRINGER,
KLARKTEKNIK, MIDAS, BUGERA, AND TURBOSOUND
ARE PART OF THE MUSIC GROUP MUSICGROUP.COM.
ALL TRADEMARKS ARE THE PROPERTY OF THEIR
RESPECTIVE OWNERS. MUSICGROUP ACCEPTS NO
LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED
BY ANY PERSON WHO RELIES EITHER WHOLLY OR
IN PART UPON ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN. COLORS AND
SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.
MUSIC GROUP PRODUCTS ARE SOLD THROUGH
AUTHORIZED FULLFILLERS AND RESELLERS ONLY.
FULLFILLERSAND RESELLERS ARE NOT AGENTS OF
MUSICGROUP AND HAVE ABSOLUTELY NO AUTHORITY
TO BIND MUSICGROUP BY ANY EXPRESS OR IMPLIED
UNDERTAKING OR REPRESENTATION. THIS MANUAL
IS COPYRIGHTED. NO PART OF THIS MANUAL MAY
BE REPRODUCED OR TRANSMITTED IN ANY FORM
OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,
INCLUDING PHOTOCOPYING AND RECORDING OF ANY
KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS
WRITTEN PERMISSION OF MUSICGROUPIPLTD.
ALL RIGHTS RESERVED.
© 2013 MUSICGroupIPLtd.
Trident Chambers, Wickhams Cay, P.O. Box 146,
Road Town, Tortola, British Virgin Islands
For the applicable warranty terms and conditions
and additional information regarding MUSIC Group’s
Limited Warranty, please see complete details online at
www.music-group.com/warranty.
4 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
1. Introduction
The demands placed on a guitar amp are nowadays very broad. A guitarist should
oer a wide array of sounds. That’s why it is very important to us to be able to
oer you maximum sound diversity as well as a variety of connection possibilities
with your VIRTUBE. Don’t worry: you will quickly master the VIRTUBE and learn
how to use all of its capabilities easily and intuitively. With its up-to-date
circuitry, the VIRTUBE features the functionality and reliability of a truly modern
guitar amp.
VTC Virtual Tube Circuitry
The specially developed VTC Virtual Tube Circuitry gives your sound the unique
vintage avor of classic tube amps.
1.1 Before you get started
Your product was carefully packed at the factory to ensure safe transport.
Nevertheless, if the box is damaged inspect the unit immediately for signs
of damage.
If the unit is damaged please do NOT return it to us, but notify your
dealer and the shipping company immediately; otherwise, claims for
damage or replacement may not be granted.
Otherwise, always use the original box to prevent damage during
storage or transport.
Make sure that children cannot play unsupervised with the unit or
its packaging.
Please ensure proper disposal of all packing materials.
Recylce whenever possible.
Ensure adequate air supply and to avoid overheating do not place the unit
near radiators etc.
Please make sure that all devices are properly grounded/earthed.
For your own safety, never remove or disable the ground/earth
conductors from the devices or on the power cords. The unit
must always be connected to the mains outlet with a protective
grounding connection.
1.1.1 Online registration
Please register your new BEHRINGER equipment right after your purchase
by visiting http://behringer.com and read the terms and conditions of our
warranty carefully.
Should your BEHRINGER product malfunction, it is our intention to have it
repaired as quickly as possible. To arrange for warranty service, please contact
the BEHRINGER retailer from whom the equipment was purchased. Shouldyour
BEHRINGER dealer not be located in your vicinity, you may directly contact
one of our subsidiaries. Corresponding contact information is included in the
original equipment packaging (Global Contact Information/European Contact
Information). Should your country not be listed, please contact the distributor
nearest you. A list of distributors can be found in the support area of our website
(http://behringer.com).
Registering your purchase and equipment with us helps us process your repair
claims more quickly and eciently.
Thank you for your cooperation!.
2. Control Elements
(2) (17)
(1) (3)
(4) (5) (6) (7) (8) (10) (11) (12) (13) (14) (15) (16) (20) (21) (22) (23 ) (24) (25) (26)
(18) (19)
(9)
Fig. 2.1: VIRTUBE control elements (front panel)
2.1 Front panel
(1) The INPUT socket is the ¼" connector for your guitar. Please use a standard
¼" TS connector.
2.1.1 CLEAN CHANNEL
(2) The CLEAN CHANNEL LED lights up when the CLEAN channel is active.
(3) The GAIN control determines the volume of the CLEAN channel.
(4) The CRUNCH button (VT100FXH and VT100FX only) allows you to add some
slight distortion to your clean sound, giving it a bit of “dirt” or “crunch”.
(5) The BASS control in the EQ section allows you to raise or lower the bass
frequencies on the CLEAN channel.
(6) With the MIDDLE control you can raise or lower the midrange frequencies
onthe CLEAN channel.
(7) The TREBLE control adjusts the treble frequencies on the CLEAN channel.
(8) Press the CHANNEL button to switch between the CLEAN and OVERDRIVE
channels. The channel LED lights up when the channel is activated. With all
models you can also switch between channels using the footswitch provided.
2.1.2 OVERDRIVE CHANNEL
(9) The OVERDRIVE CHANNEL LED lights up when the channel is active.
(10) The GAIN control determines the amount of gain applied and hence the
degree ofdistortion in the OVERDRIVE channel.
(11) The OD1/OD2 button (VT100FXH and VT100FX only) switches between
twodierent overdrive sounds.
(12) The BASS control in the EQ section allows you to raise or lower the bass
frequencies on the OVERDRIVE channel.
5 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
(13) With the MIDDLE control (VT100FXH and VT100FX only) you can raise or
lower the midrange frequencies on the OVERDRIVE channel.
(14) The TREBLE control adjusts the treble frequencies on the OVERDRIVE channel.
(15) Use the CONTOUR control for additional, highly characteristic adjustment
of the midrange, allowing you to easily create traditional as well
as ultra-modern guitar sounds.
(16) The VOLUME control adjusts the volume level of the OVERDRIVE channel.
2.1.3 DIGITAL FX
(17) The DIGITAL FX LED lights up when the eects processor is active.
(18) Use the FX PRESET control to select one of 16 eects.
Preset FX
1 - 4 Chorus/Delay
5 - 8 Delay
9 - 12 Chorus
13 - 16 Flanger
Tab. 2.1: Eects
(19) The FX LEVEL control adjusts the mix ratio between the original and
the eect signal.
(20) The REVERB LEVEL control determines the eect intensity of the
additional reverb eect.
(21) The FX LOOP MIX control (VT100FXH and VT100FX only) determines
the eect intensity of the external eect (see Chapter 2.2.1 FX LOOP).
2.1.4 MASTER section
(22) The MASTER VOLUME control adjusts both the overall volume and
the line out/headphones volume.
(23) The VTC push button activates and deactivates the VTC Virtual Tube Circuitry.
(24) The CD IN connector allows you to connect the output signal of a CD player,
tape deck, or CD/MD walkman. For example, you can play back music CDs or
CDs accompanying a guitar tutor while practising. This connector can also
be used as a LINE OUT output. In this case, the guitar signal is output with no
speaker simulation applied and can be routed to an external amp or mixing
console. This will not mute the VIRTUBE’s built-in loudspeaker.
(25) The LINE OUT/PHONES jack is for headphones connection. Internal speaker
simulation is applied to the headphones signal in order to produce an
authentic signal. The VIRTUBE’s built-in loudspeaker is muted when this
connector is used.
The headphones output signal can also be routed to a mixing console or
other sound reinforcement system. To do so, connect the headphones
output with the line input on the mixing console. Use a standard cable
with 1/4" TS connectors. If hum problems occur, you could insert a
DI box, e.g. BEHRINGER ULTRA-DI DI100 or DI120.
Some headphones tend to produce distortion with too high
volume level. Please turn down the volume a bit, until distortion stops.
(26) The POWER switch turns your VIRTUBE on and o. It should always be in the
OFF position when connecting the unit to the mains.
Please note: Merely switching the unit off does not mean that it is fully
disconnected from the mains. To disconnect the unit from the mains,
pull out the mains connector. Before installation, please make sure
that the mains connector has not been damaged. If you do not use the
unit for an extended period of time, please disconnect it at the mains.
2.2 Rear panel
(27) The VIRTUBE is connected to the mains using a standard IEC receptacle.
A suitable power cord is included with the unit.
(28) FUSE HOLDER/VOLTAGE SELECTOR. Before connecting the unit to
the mains, ensure that the voltage setting matches your local voltage.
Blown fuses must be replaced with a fuse of the same type and rating.
On some units, the fuse holder can be switched to one of two positions,
i.e. 230 V and 120 V. Please note: when operating the unit outside Europe at
120 V, a higher fuse rating is required (see Chapter 4, “Installation”).
(29) This is where the fan of the unit is located.
(30) The SPEAKER OUT connectors (only one on the VT100FX and VT50FX)
can be used to connect external speakers with a miminum impedance of
4 Ω. The outputs of the VT250FX deliver 50 Watts of power per channel
(L/R). Always use speakers with a minimum impedance of 8 Ω to ensure
maximum power output. Using the SPEAKER OUT connectors will mute the
built-in loudspeakers.
2.2.1 FX LOOP
(31) The FX LEVEL button allows you to adapt the FX LOOP to the operating level
of an external eects device (+4 dBu/-10 dBV).
(32) The VIRTUBE provides a serial insert path for inserting external eects
(e.g. reverb processor). To do so, connect the FX SEND jack to the input of the
eects device.
The FX SEND can also be used as a parallel output with no effects,
for example, to record a “dry” guitar signal. As long as the RETURN jack
is not in use, there will be no break in the internal signal path.
(28)
(27) (29)
(30) (35)
(33) (31) (32) (34)
Fig. 2.2: VIRTUBE control elements (rear panel)
6 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
(33) Connect the FX RETURN jack to the output of the external eects device.
The VT250FX has two jacks (L/R) because it is a stereo amplier.
(34) Use the FOOTSWITCH jack to connect the ¼" TRS plug of the footswitch
supplied with the unit. The footswitch performs a dual function: it switches
between the two channels and turns the DIGITAL FX on and o.
(35) SERIAL NUMBER.
3. Application Examples
The VIRTUBE features plenty of connectors for a wealth of applications.
Here’s a few examples of how exible your VIRTUBE can be:
3.1 Set-up for practicing with playbacks
HPS3000
VIRTUBE VT50FX
CD Player
Drum Computer
CD In
Footswitch
Electric Guitar
Fig. 3.1: VT50FX standard set-up
For practising in the rehearsal room or at home, please wire your VIRTUBE as
shown in Fig. 3.1. Connect a CD player or drum computer to the CD IN input.
If you want to practice with headphones, connect your headphones to the
PHONES jack. The built-in loudspeaker will be muted automatically. Connect the
dual footswitch supplied with the unit to the FOOTSWITCH jack on the VIRTUBE.
The CHANNEL footswitch switches between the channels. The EFFECT button
switches the eect on and o.
3.2 Recording set-up with eects device
VIRTUBE VT100FX
DSP2024P
FX In FX Out
FX Send FX Return
Line Out
Electric Guitar
Footswitch
DAT Recorder
Fig. 3.2: Recording set-up with the VT100FX
If you want to use your VIRTUBE in a home-recording or studio environment,
please wire it as shown in Fig. 3.2. Of course, you can still use a CD player
or drumcomputer in this set-up. This is not shown here to provide for a
better overview. Connect the input of the eects device to the FX SEND and
theeectsoutput tothe FX RETURN.
If you want to record your guitar signal with eects, connect the PHONES output
to your mixing console, audio sequencer or multi-track recorder.
To record a “dry” guitar signal with no eect, it is best to use the FX SEND
connector. You can use both outputs at the same time, for example, to record
signals via the FX SEND output (no eect), while monitoring them via the PHONES
output (with eect).
Instead of an external 19" eects processor, you can also use a wah-wah pedal
orother stomp box. However, please note that the FX LOOP is post-preamp,
i.e. after the distortion stages.
7 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
3.3 Live set-up with external speaker box
Electric Guitar
Footswitch
VIRTUBE VT250FX
BG412S
Mixing Console
Loudspeaker
Output Left
GI100
Loudspeaker
Output Right
Fig. 3.3: Set-up comprising VT250FX and one speaker box
Fig. 3.3 shows how the LINE OUT signal is routed to a mixing console. You can
connect external guitar speaker boxes to the SPEAKER OUT outputs of the
VIRTUBE (VT100FX and VT50FX have only one output) to achieve more power
and higher volume levels on stage. When the VT250FX is used, we recommend
connecting two separate speaker cabinets for stereo applications or one stereo
cabinet (e.g. BEHRINGER ULTRASTACK BG412S).
3.4 Wiring the VT100FXH
The VT100FXH has two SPEAKER OUT outputs for connection of one or two
external speaker cabinets. To achieve maximum power output on the VT100FXH,
both speaker outputs should be connected to speaker cabinets with a minimum
impedance of 4 Ω. Connecting headphones to the PHONES jack will automatically
mute the speaker outputs.
Fig. 3.4:
Loudspeaker
Output Right
VT100FXH
Loudspeaker
Output Left
Speaker Cabinets are 8 to 12 Ω each
VT100FXH with two speaker boxes
8 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
4. Installation
Except for the headphones output and the CD IN input (¼" TRS connectors),
all audio inputs and outputs on the BEHRINGER VIRTUBE are on ¼" TS connectors.
Please see Chapter 5, “Specications” for more information.
Please ensure that the unit is installed and operated only by people
qualified to do so. During installation and operation the user must have
sufficient electrical contact to earth. Electrostatic discharge may affect
the operation of the unit.
strain relief clamp
sleeve
tip
sleeve
(ground/shield)
Unbalanced ¼" TS connector
tip
(signal)
Fig. 4.1: ¼" TS connector
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.
Balanced ¼" TRS connector
ring
cold (-ve)
tip
hot (+ve)
Fig. 4.2: ¼" TRS connector
R
L
R
L
ring
tip
sleeve
tip
tip
sleeve
sleeve
Fig. 4.3: Stereo adapter cable
sleevesleeve
tiptip
Fig. 4.4: Mono adapter cable
9 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
5. Specications
VT250FX
Audio Inputs
Input ¼" TS, RF ltered
Input impedance approx. 1 MΩ, unbalanced
FX Return 2 x ¼" TS
Input impedance approx. 33 kΩ, unbalanced
CD In ¼" TRS
Input impedance approx. 5.6 kΩ, unbalanced
Audio Outputs
FX Send ¼" TS
Output impedance approx. 5.6, kΩ unbalanced
Line Out / Phones ¼" TRS, unbalanced
Output level max. +16 dBV / 100 Ω
Loudspeaker Outputs
Type 2 x ¼"
Min. load impedance 2 x 8 Ω
Amplier
Peak power 2 x 50 Watts / 8 Ω
Digital Signal Processing
Converter 24-bit, sigma-delta
Sample rate 40 kHz
Loudspeaker
Size 2 x 12"
Model BUGERA Vintage Guitar Series 2 x 12G50J8
Impedance 2 x 8 Ω
Continuous power (IEC268-5) 2 x 50 Watts
Peak power 2 x 200 Watts
Power Supply
Power consumption max. 180 Watts
Fuse
100 V~, 50/60 Hz T 3.15 A H 250 V
120 V~, 50/60 Hz T 2.5 A H 250 V
220 - 230 V~, 50/60 Hz T 1.25 A H 250 V
Mains connection Standard IEC receptacle
Dimensions / Weight
Dimensions (H x W x D) 520 x 670 x 275 mm
(20.5 x 26.3 x 10.8")
Weight 22.2 kg (48.8 lbs)
10 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
VT100FX
Audio Inputs
Input ¼" TS, RF ltered
Input impedance approx. 1 MΩ, unbalanced
FX Return ¼" TS
Input impedance approx. 33 kΩ, unbalanced
CD In ¼" TRS
Input impedance approx. 5.6 kΩ, unbalanced
Audio Outputs
FX Send ¼" TS
Output impedance approx. 8.2, kΩ unbalanced
Line Out / Phones ¼" TRS, unbalanced
Output level max. +16 dBV / 100 Ω
Loudspeaker Outputs
Type ¼"
Min. load impedance 4 Ω
Amplier
Peak power 100 Watts / 4 Ω
Digital Signal Processing
Converter 24-bit, sigma-delta
Sample rate 40 kHz
Loudspeaker
Size 12"
Model BUGERA Vintage Guitar Series 12G70J4
Impedance 4 Ω
Continuous power (IEC268-5) 70 Watts
Peak power 280 Watts
Power Supply
Power consumption max. 180 Watts
Fuse
100 V~, 50/60 Hz T 2.5 A H 250 V
120 V~, 50/60 Hz T 2.5 A H 250 V
220 - 230 V~, 50/60 Hz T 1.0 A H 250 V
Mains connection Standard IEC receptacle
Dimensions / Weight
Dimensions (H x W x D) 550 x 580 x 275 mm
(21.6 x 22.8 x 10.9")
Weight 20.4 kg (44.9 lbs)
11 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
VT50FX
Audio Inputs
Input ¼" TS, RF ltered
Input impedance approx. 1 MΩ, unbalanced
FX Return ¼" TS
Input impedance approx. 33 kΩ, unbalanced
CD In ¼" TRS
Input impedance approx. 5.6 kΩ, unbalanced
Audio Outputs
FX Send ¼" TS
Output impedance approx. 5.6, kΩ unbalanced
Line Out / Phones ¼" TRS, unbalanced
Output level max. +16 dBV / 100 Ω
Loudspeaker Outputs
Type ¼"
Min. load impedance 8 Ω
Amplier
Peak power 60 Watts / 8 Ω
Digital Signal Processing
Converter 24-bit, sigma-delta
Sample rate 40 kHz
Loudspeaker
Size 12"
Model BUGERA Vintage Guitar Series 12G50J8
Impedance 8 Ω
Continuous power (IEC268-5) 50 Watts
Peak power 200 Watts
Power Supply
Power consumption max. 90 Watts
Fuse
100 V~, 50/60 Hz T 1.6 A H 250 V
120 V~, 50/60 Hz T 1.25 A H 250 V
220 - 230 V~, 50/60 Hz T 630 mA H 250 V
Mains connection Standard IEC receptacle
Dimensions / Weight
Dimensions (H x W x D) 520 x 515 x 275 mm
(20.5 x 20.3 x 10.8")
Weight 16.5 kg (36.3 lbs)
12 VIRTUBE VT250FX/VT100FX/VT50FX/VT100FXH User Manual
VT100FXH
Audio Inputs
Input ¼" TS, RF ltered
Input impedance approx. 1 MΩ, unbalanced
FX Return ¼" TS
Input impedance approx. 33 kΩ, unbalanced
CD In ¼" TRS
Input impedance approx. 5.6 kΩ, unbalanced
Audio Outputs
FX Send ¼" TS
Output impedance approx. 8.2, kΩ unbalanced
Line Out / Phones ¼" TRS, unbalanced
Output level max. +16 dBV / 100 Ω
Loudspeaker Outputs
Type 2 x ¼"
Min. load impedance 4 Ω
Amplier
Peak power 100 Watts / 4 Ω
Digital Signal Processing
Converter 24-bit, sigma-delta
Sample rate 40 kHz
Loudspeaker
Size —
Model —
Impedance —
Continuous power (IEC268-5)
Peak power
Power Supply
Power consumption max. 180 Watts
Fuse
100 V~, 50/60 Hz T 2.5 A H 250 V
120 V~, 50/60 Hz T 2.5 A H 250 V
220 - 230 V~, 50/60 Hz T 1.0 A H 250 V
Mains connection Standard IEC receptacle
Dimensions / Weight
Dimensions (H x W x D) 250 x 580 x 270 mm
(9.8 x 22.8 x 10.6")
Weight 12.7 kg (27.9 lbs)
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts,
modifications may be made from time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or illustrated.
We Hear You
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Behringer VT250FX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Behringer VT250FX in the language / languages: English as an attachment in your email.

The manual is 6,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Behringer VT250FX

Behringer VT250FX User Manual - German - 13 pages

Behringer VT250FX User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info