573642
14
Zoom out
Zoom in
Previous page
1/24
Next page
2. BEFORE INSTALLATION
Before using this system, please read the instructions that follow to guide you through the installation and future use of this product.
• Strictly follow the regulation of your country
For safety reasons, it is best not to handle or see the monitor while driving. Park your car in a safe location to observe the monitor and
manipulate the system.
• Do not insert your hand, finger or other object within the system when the monitor is running. This can cause damage and malfunctions. Keep
small objects out of reach of children.
After long exposure to the sun, let the system cool before reuse.
Installation
For your comfort and safety please observe the following information to install this product.
The monitor should be placed at a location with good visibility for the driver.
The location of the monitor should not affect the use of operating the car, airbags and other systems.
The system runs on 12 V DC (or 24V depending on model). Be sure the vehicle voltage and polarity of each wire.
• Before installation, if all vehicle components are working properly such as contact & engine start switch codes, and fog lights, flashing lights,
heating, air conditioning, power door locks, ... Check after installing all these elements.
• Do not connect the wire by splicing / soldering without using lugs. The connections may create serious problems with the system or vehicle.
When you connect the general ground of the system, it is very important that this ground is completely open and stable (no leakage).
• Ensure that every wire passing in tight spaces are protected by adhesive tape to avoid excessive twisting and degradation of the plastic wire
with a risk of bad contacts.
Please ensure that the wire of the system and all safety devices are best possible hidden in the vehicle, always remember that you install a
security system.
• Use a digital multimeter to identify each of the polarities of the wire, using a test light to locate the tach wire (if necessary).
• Please do not disconnect the battery if the vehicle has a radio code.
• If the vehicle is equipped with an airbag, do not disconnect the car battery.
Humidity and condensation
• If the ambient temperature changes quickly, condensation may appear inside the monitor. The sytem returns to its original state after a short
time due to evaporation of moisture.
Multiplexed vehicles
The system can be installed on multiplexed vehicles. Only these electrical connections are required :
• + 12V. (Permanent, after ignition, reversing light)
• Ground
All this information is on regular wire at normal polarity (+ or -) which does not pass information encoded (multiplexed CANBUS, VAN or other
encoding). You should absolutely not cut or touch a coded wire (canbus).
IN ALL CASES, IT IS UNNECESSARY AND RECOMMENDED FOR CUTTING AN ORIGINAL WIRE OF THE VEHICLE. YOU MUST MAKE ONLY ONE
SPLICE AND RECOVER THE POSITIVE OR NEGATIVE SIGNAL PASSING THROUGH THIS WIRE.
BEEPER systems are fully compatible with the entire European car fleet and the installation can not cancel or modify the conditions of the vehicle
warranty. For information or advice, we ask that you contact our Technical Services (0892690792).
14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beeper RWEC100X-RF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beeper RWEC100X-RF in the language / languages: English, French as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info