522415

Beem Power Generator EVO3 Pro-C Manual

22
Zoom out
Zoom in
Previous page
1/56
Next page
BEEM – Elements of Lifestyle
22/56
NOTE: Hang the washing to be ironed where heat and moisture cannot cause
any damage. Never hang the washing in front of wallpaper, windows or mirrors.
ATTENTION: The steam pipe gets hot after long steam operation.
7. Use the same procedure as for normal steam ironing to switch off.
6.4 Dry ironing
1. Put the plug into the socket.
2. Switch on the steam generator.
The indicator light comes on and a beep tone is sounded.
3. Press the steam volume button until all the steam indicator lights are off.
4. Select the desired ironing temperature with the temperature selector switch.
The selected setting flashes whilst the iron is heating up. The ironing temperature is
reached when it stops flashing.
NOTE: Press the steam button about every 15 minutes, otherwise the automatic
switch-off function will become active and the utensil switch off.
5. Set the iron to level • to switch off and replace it on the steam generator.
6. Press the
button on the steam generator and then pull out the mains plug.
7. Faults and troubleshooting
The utensil is equipped with a safety valve. If the steam pipe is blocked, the safety valve
opens and the steam escapes under the utensil. This produces a high whistle. If this is the
case, switch off the utensil immediately, pull out the plug and check the steam pipe for
possible damage or kinks. If you cannot find anything wrong, clean the utensil as described in
section 8 and change the filter cartridge (section 8.3).
Faulty
function
Possible reason Remedy
The utensil is not switched on. Switch the utensil on with the on/off
switch on the steam generator.
The steam iron
stays cold.
The temperature is on •. Set the necessary temperature.
The steam generator is not switched
on.
Switch on the steam generator.
The filter is not inserted in the water
tank.
Insert the filter in the water tank.
The water tank has hardly any water
in it or is empty.
Fill with water.
The utensil does
not produce
steam.
The water tank is not inserted in the
steam generator correctly.
Insert the water tank so that it clicks in
audibly.
The steam pressure button has been
kept pressed for too long and the
Heat indicator on the steam
generator lights up.
Wait until the iron has reheated. The Heat
indicator on the steam generator goes
out. If this does not help, select a lower
steam volume briefly.
Water drips
from the sole of
the iron. This is
normal when
starting ironing
or after short
breaks (cold
hose and the
steam
condenses).
The temperature of the iron is off
(position •) or too low (position
Synthetic).
At least level Wool/Silk must be selected
for steam ironing. Select a higher
temperature on the iron.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beem Power Generator EVO3 Pro-C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beem Power Generator EVO3 Pro-C in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info