712825

Beem 03840 - Robustica Manual

32
Zoom out
Zoom in
Previous page
1/86
Next page
EN 28
Drip Stop
The device has a drip stop which stops coffee dripping from the coffee tank (2) while the coffee
dispenser (6) is not being pressed.
During the brewing process and while the device is in operation, care must be taken to ensure
that nothing constantly presses against the coffee dispenser.
Preparation
NOTICES
• Do not operate the device without water or with less water than is required to reach
the 2 Cups mark. If this does happen, the device switches off automatically. In this case,
allow the device to cool down before water is poured in and the device is used again.
• Never detach the coffee tank to transport or serve hot coffee.
• Never press the coffee dispenser without a suitable vessel placed below the coffee
outlet.
1. Fill the water tank (7) (see the “Handling and Operation” chapter – “Filling the Water
Tank ”).
2. Insert the permanent fi lter or a basket fi lter paper (see the “Handling and Operation”
chapter – “Inserting the Filter”).
3. Add the quantity of coffee powder you want to the fi lter using the measuring spoon which
is supplied with the device or another suitable spoon. We recommend one heaped measur-
ing spoon for each 125 ml cup (Picture B).
4. Close the lid (1).
5. If necessary, set the desired brew strength with the BRÜHSTÄRKE (brew strength)
button(15) (see the “Handling and Operation” chapter – “Setting the Brew Strength”).
6. If you wish, set the keep-warm function using the WARMHALTEN (keep warm)
button(12) (see the “Handling and Operation” chapter – “Keep-Warm Function”).
7. Press the START / STOP button (16) to start the brewing process. The operating lamp in
the button lights up. The water is transported from the water tank through the fi lter into
the coffee tank (2) and kept warm inside it (PICTURE C).
8. The fi ll-level indicator (3) indicates how much coffee is in the coffee tank (Picture D).
At the end of the brewing process, you will hear a beep and the device automatically switches
on the keep-warm function (see the “Handling and Operation” chapter – “Keep-Warm
Function”). The operating lamp in the
START / STOPP (start / stop) button remains switched
on.
If the brewing process is to be aborted prematurely, press the START / STOPP
(start / stop) button. The operating lamp goes out, and the device is in stand-by mode.
03840_DE-EN-FR-ES-IT_Inlay_A5_V3.indb 2803840_DE-EN-FR-ES-IT_Inlay_A5_V3.indb 28 16.01.2019 09:44:2216.01.2019 09:44:22
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Beem 03840 - Robustica at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Beem 03840 - Robustica in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info