766343
5
Zoom out
Zoom in
Previous page
1/24
Next page
5
REMOTE CONTROLL
Button function:
1. 151.200/151.202 Red LED (on /off), 151.201 ¼ Cool white (on/off)
2. 151.200/151.202 Green LED (on/off) , 151.201 ¼ Cool white (on/off)
3. 151.200/151.202 Blue LED (on/off) , 151.201 ¼ Cool white (on/off)
4. 151.200/151.202 White LED (on/off) , 151.201 ¼ Cool white (on/off)
5. Sound control
6. Strobe (keys 9+10 for speed up/down)
7. Fade (keys 9+10 for speed up/down)
8. Auto mode (keys 9+10 for speed up/down)
9. Up (speed)
10. Down (speed)
11. Enter/Confirm
12. DMX512 control
REPLACING THE FUSE
If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.
REPLACING THE LEDS
Compared to incandescent lamps, LEDs have a very long life and usually no replacement is required. However, just in case
there is a defect, a few spare LED modules are supplied.
1. Separate the cable connection between the LED curtain and the controller.
2. Open the zip fastener at the side of the LED curtain; the connections of the LED modules will be accessible.
3. Before disconnecting the plugs from the defective module, note the polarity (small marks “+” and “-” on the PCB). If
necessary, remove the retaining adhesive at the connectors in order to disconnect the plugs.
4. Connect the spare module using the same polarity.
5. From the front of the cloth, pull the black plastic ring around the LED from the PCB of the defective module and remove
the module.
6. Insert the LED of the spare module from the rear through the hole in the cloth and, from the front, insert a black plastic
ring through the cloth so that the two pins will engage in the corresponding holes provided on the PCB.
7. After replacing the necessary modules, close the zip fastener again.
FIXTURE CLEANING
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding
can cause greater accumulation of dirt on the unit’s optics.
Make sure the area below the installation place is free from unwanted persons during servicing.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any deformation.
The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is
detected.
In order to protect the fixture from overheat the cooling fans (if any) and ventilation openings should be cleaned
monthly.
The interior of the fixture should be cleaned annually using a vacuum cleaner or air-jet.
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Clean the external optics at least every month. Clean the internal optics at least every 30/60 days.
ATTENTION: We strongly recommend internal cleaning to be carried out by qualified worker!
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 151.200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 151.200 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info