If you are using a standard DMX controller, you can connect the DMX output of the controller directly to the DMX input of the first unitin a DMX chain.
Always connect the output of one unit with the input of the next unituntil allunitsare connected.
CAUTION!At the lastunit, you must close the DMX line with a terminating resistor. Take an XLR connector and solder a 120 Ohm resistor
between signal (-) and signal (+) and connect it to the DMX output of the last unitin the line.
PROTECTION CLASS IP65
Units with protection class IP65 are dust-tight and completely protected against contact (first code number). They are also protected against splash water
from any angle (second code digit). That is why this unitcan also be used out‐doors. Events unitsaregenerally only designed for temporary use however
(event lighting) and not for permanent use outdoors. The specified protection class does not make a statement about the weather resistance of the units
(resistance to changing ambient conditions as well asagainst the effects of sunlight and UV rays). The seals and screw connections of the unitsmust be
checked regularly to ensure a fault-free operation.
MAINTENACE
This unitis virtually maintenance-free, but you should check the unitregularly for mechanical and electrical aspects.
Assess the operating environment and establish an inspection and cleaning schedule that follows the guidelines below:
•Disconnect the unitfrom the power supply and allow it to cool completely before inspecting and cleaning.
•Check that the screws and boltsused to install the unitare securely tightened and free from corrosion.
•Check the housing, fixing points and installation points, they must not show any signs of deformation, wear or fatigue.
•Check the mechanically moving parts, these must not show any signs of wear or fatigue.
•Check the electricalpowerand signal cables, they must not show any damage or fatigue.
•Do not use solvents, abrasives or other aggressive products to clean the unit.
•Wipe the unitand clean the glass plate with a soft, clean, lint-free cloth moistened with a weak cleaning solution. Place the solution on the cloth
and not on the surface to be cleaned. Avoid rubbing glass surfaces.
•Dry the unit, connectors and contacts with a soft, clean, lint-free cloth or low-pressure compressed air before re-powering the unit.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for BeamZ 150.732 - STARCOLOR at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of BeamZ 150.732 - STARCOLOR in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.
The manual is 2.12 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
