CAUTION!Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present,and
have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from
shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to
the factory, it is important that the product be returned in the original factory box and packing.
If the unithas been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arisingcondensation water
might damage your unit. Leave the unitswitched off until it has reached room temperature.
POWERSUPPLY
On the label on the backside of theunitis indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all
other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No
dimmer or adjustable power supply.
The unit has a powerconnector outputon board. Depending on the local conditionsseveral unitscan be linked by powerconnectorin- and output. Connect
a maximum of four (when using 230V/16A) unitsin a row.Use an approved three-core cable with a cross-section of at least 1.5 mm². The installation
instructions of the manufacturerand the colour coding of the cable must be observed.Do not turn off the unit by turning the powerconnectorbut use the
poweron/off switch or schuko!
WARNING!Always connect the unitto a protected circuit (circuit breaker or fuse). Make sure the unithas an appropriate electrical ground to
avoid the risk of electrocution or fire.
RIGGING
In temporary installations, you can suspend the fixture from a rigging truss by means of a rigging clamp that is approved for the weight of the fixture
securely fastened through the hole in the center of the bracket (A). The fixture must be installed hanging vertically downwards only. When using a rigging
clamp, secure the fixture with a safety cable, that is approved for the weight of the fixture so that the safety cable will hold the fixture if the rigging clamp
fails. Remove as much slack as possible from the safety cable (by looping it more than once around the truss chord, for example). Check thatthe truss and
all fasteners used can support 10 times the weight of all the fixtures and equipment that they will support.
When carrying out any installation, always comply European and national guidelines concerning rigging, truss and all other safety issues. Always let the
installation checkedout by an authorized dealer!
MOUNTING ON A SURFACE
To anchor the mounting bracketto a wall or other flat surface, use three high-strength corrosion-resistant fasteners that are safe for the application. Use
selflocking nuts! Install washers under all nuts and bolt heads. Make sure that there is a washer between each fastener and the bracket. Ensure that the
surface and all fastenersused can support 10 times the weight of all the fixtures and equipment that they will support.
Fasten the center of the bracketwith a 10 mm (25/64inch) shaft diameter bolt in the centerhole A. Then use two bolts with 8 mm (5/16 inch) shaft
diameter passing through the curved slots B to anchor the fixture. This setup will give approximately 90° of pan adjustment.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for BeamZ 150.732 - STARCOLOR at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of BeamZ 150.732 - STARCOLOR in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.
The manual is 2.12 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
