766342

BeamZ 150.303 - MHL820 Manual

5
Zoom out
Zoom in
Previous page
1/52
Next page
5
SLND - This will let you set unit as a master or slave in a
master/slave configuration.
1. Press the MENU button until “SLND” is displayed, press ENTER. Either
“MAST”, “SL 1”, or “SL 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press
ENTER to confirm.
NOTE: In a Master/Slave configuration you can set one fixture to Master and
then set the next fixture to “SL 2”, the fixtures will now have contrast movement
to each other.
SHND - Show modes 0-8 (Factory programs). Show mode can run with or
without sound active mode active.
1. Press the MENU button until “SHND” is displayed, press ENTER.
2. “Sh X” will now be displayed, “X” representing a number between 0-8. Use the UP or
DOWN buttons to find your desired show.
3. When you have found your desired show press ENTER, then press and hold the
MENU button for at least 3 seconds to activate. After you have set your desired show, it
can be changed at any time using the UP or DOWN buttons
SOUN - Sound Active mode.
1. Press the MENU button until “SOUN” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select
“ON” to activate sound active mode, or “OFF” to deactivate sound active mode.
3. Press ENTER to confirm.
SENS - In this mode you can adjust the sound sensitivity.
1. Press the MENU button until “SENS” is displayed, press ENTER.
2. A number between 0-100 will be displayed. Press the UP or DOWN buttons to adjust
the sound sensitivity. 0 being the least sensitive, and 100 being the most sensitive.
3. When you have found your desired setting press ENTER to confirm.
DNST - This mode can be used as a precaution mode, that in case the
DMX signal is lost, interrupted, or power is lost, the operating mode
chosen in the setup is the running mode the fixture will go into when the
DMX signal is lost. You can also set this as the operating mode you would
like the unit to return to when power is applied.
1. Press the MENU button until “DNST” is displayed, and either “MASL”, “BLND”, or
“LAST” will be displayed beneath.
2. Press ENTER and the bottom choice will begin to flash. Use the UP or DOWN buttons
to choose an operating mode you would like the unit to start up in when power is applied
or the DMX signal is lost.
• LAST - If the DMX signal is lost the fixture will stay in the last DMX setting. If power is
applied and this mode is set, the unit will automatically go into the last DMX set up.
• MASL (Master Slave) - If the DMX signal is lost or power is applied, the unit will
automatically go into Master Slave mode and run a built-in show.
• BLND (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go
into standby mode.
3. Press ENTER to confirm your desired set up.
DIND - This will let select your desired dimmer curve.
1. Press the either the MENU button until “DIND” is displayed, press ENTER. 1 of 5
dimmer curves will be displayed. “STDA” (standard), “STGE” (stage), “TV” (TV), “ARAL”
(theatrical), or “THAL” (Architectural).
2. Press the UP or DOWN buttons to find your desired dimmer curve and press ENTER
to confirm and exit.
ENTER
MODE UP
DOWN
UP
DOWN
ENTER
MODE UP
DOWN
ENTER
MODE UP
DOWN
ENTER
MODE UP
DOWN
UP
DOWN
ENTER
MODE UP
DOWN
UP
DOWN
UP
DOWN
UP
DOWN
ENTER
MODE UP
DOWN
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BeamZ 150.303 - MHL820 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BeamZ 150.303 - MHL820 in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.

The manual is 3,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info