305996
9
Zoom out
Zoom in
Previous page
1/14
Next page
Final spin results are poor:
The appliance has an
imbalance detection and
correction system. If individual
heavy articles are loaded
(bathmat, bathrobe, etc.) this
system may reduce the spin
speed automatically to protect
the appliance or even
interrupt the spin cycle
altogether, if the imbalance is
too great even after several
spin starts.
If the laundry is still too wet
at the end of the cycle, add
other articles of laundry and
repeat the spin cycle.
Excessive foam formation
may prevent spinning.
Ensure correct amount of
detergent is used.
Check whether the spin
speed has been reduced to 0.
No water or insufficient
water pressure for
appliances with safety
hose:
the appliance has a safety
hose and the safety valve
has opened (red indicator in
the safety valve inspection
window).
In this case replace it with a
new safety hose.
What should I do when the automatic safety system detects a malfunction?
The programme is interrupted and various indicators (if available) point to the source of the fault.
Fault description table
a.Water inlet fault (no
water or insufficient
water pressure)
The “Water tap closed”
indicator is on and the
digital display shows “FH”
Switch off the appliance by
turning the programme
selector to the
position and unplug it.
Check whether:
the water tap is open and
the water supply pressure is
sufficient;
the water inlet hose is kinked;
the mesh filter between the
tap and the hose is clean (see
“Care and Maintenance” /
“Mesh filter in water
connection”);
the water supply hose is
frozen up.
Connect the appliance to the
electrical supply.
Reselect the desired
programme and press the
“Start/Pause”
button again
to continue with the
programme (do not add
detergent for this
programme).
b.Draining fault
The digital display shows
“FP”. Switch off the appliance
by turning the programme
selector to the “ ” position
and unplug it.
Check whether:
the drain hose is kinked (see
“Installation”);
the drain hose is frozen.
Connect the appliance to the
electrical supply.
Reselect the desired
programme and press the
“Start/Pause”
button again
to continue with the
programme (do not add
detergent for this programme).
If the fault re-occurs, contact
After Sales Service (See “After-
Sales Service”).
c.Electrical module fault
The digital display shows
“F4” to “F21”.
Set the programme
selector to the
position, select the
desired programme and
press the
“Start/Pause”
button again. The
programme will continue.
If the fault re-occurs,
contact After Sales Service
(SeeAfter-Sales Service”).
d.Water Stop fault
An audible tone sounds.
The light of the Water Stop
indicator goes on. The
digital display shows “FA”
and the pump is running.
The “Water Stop fault” may
have been triggered by:
too much foam.
a leak in the appliance,
water running into the
water tank.
Small lamp lights up Digital display Fault description
“Water tap closed” “FH” “Water inlet fault”
- “FP” “Draining fault”
- from “F4” to “F21” “Electrical components fault”
“Water Stop” “FA” “Water Stop fault”
4gb15150.fm Page 9 Monday, July 8, 2002 7:00 PM
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bauknecht wab 8795 big at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bauknecht wab 8795 big in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bauknecht wab 8795 big

Bauknecht wab 8795 big User Manual - German - 14 pages

Bauknecht wab 8795 big User Manual - Dutch - 14 pages

Bauknecht wab 8795 big User Manual - French - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info