The instructions below, to be carried out in the order in which they are numbered, refer to the drawings on the last few pages of this manual, which are marked with
the corresponding numbers.
IMPORTANT: The hood is supplied in 'extractor mode'.
To use the hood in 'lter mode', the carbon lter must be purchased and tted after installation.
For 'extractor mode' only: The hood is supplied with an upper exhaust outlet. If necessary, the outlet can be routed through the wall (see installation instructions).
1. Mark a vertical centre line on the wall, as far as the ceiling.
2. Place the drilling diagram against the wall (hold it in place with adhesive tape). The vertical centre line printed on the drilling diagram must match the centre
line drawn on the wall.
Please note: The bottom edge of the drilling diagram corresponds to the bottom edge of the hood.
IMPORTANT: the bottom edge of the drilling diagram must be a minimum distance of 40cm (for electric hobs) or 65 cm (for gas hobs) from the
surface of the hob.
3. Drill the holes as indicated on the drawing.
4. For 'extractor mode' only – rear outlet: Make a hole in the wall for the exhaust pipe.
5. Remove the drilling diagram from the wall, insert the two wall plugs and two screws in the upper holes in the wall, making sure that they protrude by around
5mm; insert the third wall plug in the bottom hole.
6. If you want to install the chimney section: Attach the chimney support bracket to the wall. Drill a hole and insert the wall plugs as shown. Fix the bracket in
place.
7. Only for 'lter mode' with chimney: Fit the lter connector to the chimney support bracket.
8. Only for 'lter mode' without chimney: Fit the plastic grille to the air outlet hole on the hood.
9. For 'extractor mode' only – upper outlet: Install the non-return exhaust valve.
10. Open the panel and remove the grease lter.
11. For 'extractor mode' only – rear outlet: Remove the pre-fractured cap located on the back panel of the hood, taking care not to damage it.
12. For 'extractor mode' only – rear outlet: Remove the electronic box, unscrewing the two screws that x it to the motor unit, and unhooking it from the pins on
the opposite side (keep the screws).
13. For 'extractor mode' only – rear outlet: Remove the screws that x the motor unit to the hood (keep the screws).
14. For 'extractor mode' only – rear outlet: Rotate the motor unit.
15. Fix the electronic box using the previously removed screws (see installation sequence 12).
16. For 'extractor mode' only – rear outlet: Fix the motor unit to the back panel of the hood using the previously removed screws (see installation sequence 13).
17. For 'extractor mode' only – rear outlet: Fit the previously removed cap (see installation sequence 11) using two screws, as shown.
18. Hook the rear holes in the hood over the retaining screws.
19. Insert the washer and safety screw in the lower hole. Secure the hood to the wall by tightening the two xing screws.
20. Insert the power cable in the appropriate slot. Secure the cable with the cable clamp.
IMPORTANT: This action is compulsory. It will prevent accidental disconnection of the power cable.
Connect the appliance to the household mains.
21. Fit the carbon lters, covering the motor. Turn the lters to secure them to the central pins.
22. Re-t the grease lters and close the panel.
23. If you want to install the chimney section:Rest the chimney on top of the hood, remove the top section and x the chimney using two screws, as shown.
Check that the hood is working properly, referring to the section on the description and use of the hood.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Bauknecht DBHVS82 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Bauknecht DBHVS82 in the language / languages: English as an attachment in your email.
The manual is 3,12 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
