623733

Batavus X4 Manual

11
Zoom out
Zoom in
Previous page
1/104
Next page
GB
11
OWNER'S MANUAL
•
BATAVUS
e setting.
•
Press the Mode button.
The time will blink on Display 2.
•
Use the Plus/Minus buttons for adjustment.
Continue as appropriate, or Without entering
values, press the Start button immediately and
begin training.
NOTE: The preset value in watts is constantly shown
on Display 1. The currently achieved performance
(watts) as a function of the speed can be seen on
Display 2. The bar diagram on Display 1 shows the
current resistance level. The level increases if, for
example, you pedal more slowly.
FITNESS TRAINING/FITNESS TEST
This program requires a USB stick and your
personal data to use. The machine must measure
your pulse during the entire session. Select the
Fitness program as described above using the Plus/
Minus buttons.
•
Press the Mode button.
The preset time (Display 2) is 12 minutes and
cannot be changed. A bar diagram that is also
preset and cannot be changed appears on Display
1.
•
Press the Start button to run the program.
After the time expires, the program stops and
shows you your fitness level. The maximum value
is 100. In addition, five ranges are displayed.
Bad Bad
General General
Good Good
Nice Nice
Best Best
Please do not confuse these five levels with the
Recovery function (Fitness index 1-6).
NOTE: The control panel calculates the values
during the 12-minute training session in
accordance with the user (male/female, age) and
the speed pedaled during the test.
If a correct measurement was not possible because
the pulse could not be measured continuously, the
display will show Fail.
H.R.C. TRAINING (HEART RATE CONTROL),
CONSTANT PULSE TRAINING
In this program, you can train using pulse control.
You can enter your target pulse rate or a % range.
Using the formula for the heart rate zone or the %
range, you can determine your individual target
pulse. The program increases the resistance during
training until you have achieved your preset pulse
rate, and then the program will maintain the
resistance at a constant level. All other values are
shown on Display 2.
A. Target percent range: 55% / 75% / 90% (Figure
).
B. Preset pulse rate, TAG, e.g., 130 (Figure ).
This program requires a USB stick and your
personal data to use. The machine must measure
your pulse during the entire session. Select the
H.R.C. program as already described using the
Plus/Minus buttons.
•
Press the Plus/Minus buttons to select the
percent range or TAG (preset pulse rate).
Press the Mode button.
When you have selected a percent range, the time
will blink.
•
Use the Plus/Minus buttons if you want to
train using a preset value or
•
Press the Start button to begin training
immediately.
If you have selected TAG, the pulse rate will blink.
•
Press the Plus/Minus buttons to select the pulse
rate.
•
Press the Mode button if you wish to enter
values or
•
Press the Start button to begin training without
preset values.
If you have selected the preset pulse rate, the pulse
rate is shown on Display 1.
•
Press the Plus/Minus buttons to make a
selection.
•
Press the Mode button.
•
The training time will blink.
•
Use the Plus/Minus buttons to enter values or
•
Press the Start button without input.
In either case (A / B), the resistance (Level) is
calculated and adjusted automatically. The bar
diagram on Display 1 shows the current resistance.
To adjust the resistance, the control panel requires
several seconds. This provides a gradual adjustment
for your pulse rate. If you are already training
at Level 1, the lowest level, but your pulse still
remains too high, the control panel will power off
after 30 seconds for safety reasons. You will also
hear an alarm signal.
USER TRAINING
In this program, you can create and store
individual profiles for the training session for six
users. A USB stick must be inserted.
Press the Start button when the control panel is in
Sleep mode. The background lighting is switched
off.
batavusX4.indd 11batavusX4.indd 11 12.10.2005 12:49:4012.10.2005 12:49:40
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Batavus X4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Batavus X4 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info