Manual Batavia XXL SPEED SAW Mini BT-CS001 (page 23 of 64) (English, German, Dutch, French)

589451

Zoom out

Zoom in

1/64

c) Avoid the area in front of and behind a

rotating cutting wheel. A kickback will send

the electric power tool in the opposite direction

to the movement of the grinding disc at the

point where it jams.

d) Work extremely carefully in the

neighbourhood of corners, sharp edges

etc. Prevent the tool insert from recoiling

from the workpiece and jamming. The

rotating tool insert bends at corners and sharp

edges or if it rebounds and may jam itself. This

causes a loss of control or kickback.

e) Do not use any chainsaw or toothed saw

blade, nor any segmented diamond disc,

with slots wider than 10 mm. Such tool

inserts frequently cause a kickback or loss of

control of the electric power tool.

f) Avoid jamming of the cutting wheel or too

high a contact pressure. Do not make

excessively deep cuts. An overload of the

cutting wheel increases its stress and its

susceptibility to tilting or jamming and, hence,

increases the possibility of a kickback or break

in the grinding wheel.

g) If the cutting wheel becomes jammed or if

you interrupt the work, switch the device

off and keep it held gently until the disc

has come to a standstill. Never attempt to

remove a still-running cutting wheel from

the cut, otherwise kickback may result.

Find and remove the cause for the jamming.

h) Do not switch on the electric power tool

again, while it is still in the workpiece.

Allow the cutting wheel to rst reach its full

rotation speed before carefully continuing

the cut; otherwise, the disc may snag, jump

out of the workpiece or cause a kickback.

i) Provide support for large workpieces, to

reduce the risk of a kickback through

jamming of the cutting wheel.

Large

workpieces can bend under their own weight.

The workpiece must be supported on both sides

of the disc, as well as both in the neighbourhood

of the separation cut and at the edges.

j) Be especially careful when making "pocket

cuts" in existing walls or other non-visible

areas. The immersed cutting tool can cause a

kickback when cutting into gas or water pipes,

electric cables or other objects.

2.7 SAFETY AND OPERATING INSTRUCTIONS

FOR DIAMOND GRINDING WHEELS

Use

Only use the cut off grinding disc for cut off

grinding and not for rough grinding! Only use the

cut off grinding discs for the materials indicated

and not for any other materials. Risk of injury!

Cutting and cooling!

General Information

This tool insert is fragile, therefore extreme care

is required when handling it. The use of damaged

and incorrectly tensioned or installed tool inserts

is dangerous and can result in serious injury.

Handling and storage

Tool inserts must be carefully handled and

transported. Tool inserts should be stored in such

a way that they are not exposed to any

mechanical damage or damaging environmental

inuences.

To avoid damage, remove the tool insert before

transporting an electric power tool.

Selection and safe and proper use

Pay attention to the data on the label or on the

tool insert, such as the restrictions on use, safety

instructions or other advice. Do not alter the

characteristic direction of motion of the tool insert.

If there is ambiguity over the selection of tool

inserts, contact the manufacturer or a specialist.

Adhere to the permissible rotation speeds for the

tool insert and the electric power tool.

Before use

Tool inserts must be given a visual inspection

before each start-up. Do not use damaged tool

inserts. Secure the piece to be worked on.

Inserting and changing

Tighten the tool inserts in accordance with their

instructions and those of the electric power tool's

manufacturer. The tightening of tool inserts should

only be undertaken by qualied persons. After

each tightening, carry out a test run for a suitable

length of time, during which the characteristic

maximum working speed of the tool insert may

not be exceeded.

Always tighten tool inserts without introducing any

out-of-roundness.

I have a Batavia BT-CS001 XXL speed saw . Brilliant saw but one of the windings on the motor has gone open circuit . Can you supply a new replacement motor ? Submitted on 25-4-2020 at 13:49
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Batavia XXL SPEED SAW Mini BT-CS001 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Batavia XXL SPEED SAW Mini BT-CS001

Batavia XXL SPEED SAW Mini BT-CS001 Additional guide - English, German, Dutch, French - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Batavia XXL SPEED SAW Mini BT-CS001 Manual

Product: