589450

Batavia Racer BT-CS006 Manual

28
Zoom out
Zoom in
Previous page
1/60
Next page
7.6 Line cuts (Figure 7)
You can follow a drawn line with the help of the
indicator marks (a), at the front and rear of the
safety guard. For precise work, the relationship
between the saw cut and a marked indicator line
must be established using a test piece. The ideal
positioning of the saw cuts must then be achieved
by adjusting the indicator line to the target line.
7.7 Working with large workpieces
When working with large workpieces or cutting
straight edges:
• Usefasteningclampstotightenaboardor
border onto the workpiece as an auxiliary stop.
• Guidetheleft-handsideofthebaseplate
along the auxiliary stop.
7.8 Plunge cuts (Figure 4)
Note: Some very hard materials are not suitable
for plunge cuts.
Put the base plate on the workpiece. Make sure
that the rear lateral depth marking is at the height
of the beginning of the cut.
Switch on the electric power tool and allow a
couple of seconds to pass until the tool insert
reaches its full speed.
Then plunge the tool insert, slowly but with some
pressure. Push the electric power tool forwards
through the workpiece.
When you reach the end of the cut, switch off the
electric power tool and pull it out of the workpiece.
7.9 Cutting tiles
Adhesive tape or insulation tape on the workpiece
makes the work easier and helps to prevent it
from getting scratched.
8. CLEANING AND MAINTENANCE
Warning! Pull out the power plug
before any cleaning work.
Cleaning
• Keepsafetydevices,ventilationopeningsand
the motor housing as free as possible from dirt
and dust. Rub the electric power tool with a
clean cloth or blow over it with low pressure
compressed air.
• Werecommendthatyoucleanyourelectric
power tool immediately after each use.
28
TM
forward feed speed.
Overload indicator (2) continually lit: The electric
power tool is overloaded or jammed - the electric
power tool cuts out. In this event, switch the electric
power tool off and allow it to cool down before using it
again.
7.5 Use
Warning! Always begin by making a
test cut in a left-over piece.
• Firmlyclampsmallwoodenpiecesbefore
commencing work. Never hold them in your
hand.
• Fullyobservethesafetyregulations!
Wear safety glasses!
• Adjustthecuttingdepthandrotationspeed.
• Pickuptheelectricpowertoolandmakesure
that none of the ventilation openings are
covered.
• Switchontheelectricpowertoolandwaitfor
several seconds until the tool insert has
attained its full rotation speed.
• Thewastepieceshouldbeontherightorleft
side of the electric power tool, so that the wide
part of the supporting table rests on its entire
surface.
• Thebaseplatemustalwaysrestatonthe
workpiece.
• Pressthereleasebutton(7)andslowlypush
the tool insert into the workpiece or, if
necessary, plunge it.
• Pushtheelectricpowertoolforwardsthrough
the workpiece. Never move it backwards!
• Applyonlyagentleforcetotheelectricpower
tool when working.
• Ifsawingalongamarkedline,leadtheelectric
power tool along the appropriate groove.
• Iftheoverloadindicator(2)ashes,reduce
your speed.
• Iftheelectricpowertoolstopsandthe
overload indicator (2) is lit continuously, then
the overload protection of the electric power
tool has responded. Reason: You were moving
forward too quickly or have encountered an
obstacle in the workpiece. In this case, switch
off the electric power tool and inspect the
workpiece. Move forward at a slower speed.
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Batavia Racer BT-CS006 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Batavia Racer BT-CS006 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info