Manual Batavia BT-TS001 FLIPOUT (page 14 of 32) (English, German, Dutch, French)

589472

Zoom out

Zoom in

1/32

English

Warning: Do NOT leave the charger

plugged in for longer than 5 hours. The

battery will be fully charged within one

hour. Leaving the charger plugged in for

longer than 5 hours may damage the

battery.

Inserting a Bit into the Bit Connector:

Push forward metal collar and insert any ¼ in.

hex shank accessory. Release the collar to

lock the accessory in the bit connector (7).

Removing a Bit from the Bit Connector:

Push forward the metal collar to release the

accessory from the bit connector.

LED Worklight

This driver has a LED worklight (1) built into the

head of the tool. Turn the LED bulb towards the

direction of the connector to turn on. The light

will remain on while it is in the same direction

as the connector. To turn off the light, turn the

LED bulb towards the battery compartment (2).

Replacing the Worklight Battery

Remove the battery cover (2) and replace the

battery with a new one (CR927). Please

observe correct polarity, the positive pole (+) of

the battery must point to the battery compart-

ment cover.

Forward/Reverse Switch

The forward/reverse switch (3) is conveniently

mounted below the trigger switch (5). To make

the driver rotate clockwise for driving screws,

push the forward/reverse switch to the left. To

make the driver rotate counter clockwise for

removing screws, push the forward/reverse

switch to the right.

Notes:

a. Never change the position of the forward/

reverse switch while the driver is turning.

b. The trigger switch will NOT function

with the forward/reverse switch in the

middle/neutral position.

Variable Speed Trigger Switch

The cordless driver is equipped with a varia-

ble-speed trigger switch.

1. To start the driver, gently squeeze the

trigger switch (5).

NOTE: The driver will turn at its slowest speed

when the trigger switch is squeezed lightly. The

driver will turn at its fastest speed when the

trigger switch is squeezed rmly.

2. To stop the cordless driver, release the

trigger switch.

NOTE: Operating the driver at a slow speed for

an extended period of time may cause the

driver motor or the battery to overheat. If the

driver gets hot, stop operating it and allow it to

cool for at least 15 minutes.

Multi-Position Driver Head

The cordless driver has a multi-position head.

This allows the connector to move in any direc-

tion required.

1. To rotate the head 360º, push the switch

(6) towards the connector and freely rotate

the head.

2. To change the angle of the driver head

push button (13) and rotate the angle of

the head.

3. To change the angle of the connector

push button (12) and rotate the head.

MAINTENANCE AND CLEANING

Maintenance

There are no inner parts of the tool which need

maintenance.

Cleaning

• Keep safety devices, ventilation openings

and the motor housing as free as possible

from dirt and dust. Rub the electric power

tool with a clean cloth or blow over it with

low pressure compressed air.

• We recommend that you clean your elec-

tric power tool immediately after each use.

• Clean the electric power tool regularly with

a damp cloth and somewhat soft soap. Do

not use any cleaning or solvent materials;

these can attack the device’s plastic com-

ponents. Make sure that no water can get

inside the electric power tool.

7062267_FlipOut_Ma_#1503-12.indb 14 26-03-15 09:11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-TS001 FLIPOUT in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Batavia BT-TS001 FLIPOUT Manual

Product: