Manual Batavia BT-NXS001 - 7063578 (page 9 of 40) (English, German, Dutch, French)

758154

Zoom out

Zoom in

1/40

English

8. Use

8.1 Mounting the saw chain

(See Fig. C, D, E).

Always wear gloves when handling the

saw chain.

a. Unscrew the head screw (3) coun-

ter-clockwise in order to remove the

sprocket cover (2).

b. Run the saw chain over the sprocket.

Please note the running direction of the

saw chain. The saw chain icon is shown

on the cover.

c. Use an oiler to oil the saw chain and the

sprocket.

d. Slightly tighten the saw chain with the

chain adjusting screw (7). For tighten-

ing, turn the screw clockwise.

e. Re-tighten the sprocket cover (2) with

the head screw (3) on the housing.

f. Firmly tighten the saw chain with the

chain adjusting screw (7). Use the

included adjustment key (11) to tighten

the screw.

8.2 Chain lubricating oil

• Only use commercially available, biode-

gradable chain oils that are specially

designed for use in multi saws.

• Do not use engine oil, waste oil or other

mineral oils.

8.3 Adjusting saw chain tension

(See Fig. C).

CAUTION: Do not tighten the saw chain too

much. Excessively high tension of saw

chain may cause breakage of saw chain,

wear of the guide bar and breakage of the

sprocket.

CAUTION: A chain which is too loose can

jump off the guide bar.

The saw chain may become loose after

many hours of use. From time to time check

the saw chain tension before use.

a. Remove the battery.

b. Loosen the head screw (3) a bit to

loosen the sprocket cover lightly.

c. Adjust the chain tension. Turn the chain

head screw (7) clockwise to tighten,

turn it counter-clockwise to loosen.

Tighten the saw chain so that the gap

between the centre of the lower side of

the guide bar and the saw chain

becomes approximately 3 – 4 mm.

d. Tighten the head screw (3) to secure

the sprocket cover.

8.4 Switching ON and OFF

The use of the Nexxsaw without lubricating

the chain with chain oil will damage the saw

chain and the guide bar.

a. Insert the battery into the battery

recess.

b. 

by the handgrip. To switch on the Nexx-

(1)

and release the switch.

c. Then press the ON/OFF switch within 1

second (10).

d. To switch off the saw, release the ON/

OFF switch.

8.5 Break-in time for new saw chains

a. Remove the battery and adjust the

chain tension.

b. Switch on the Nexxsaw and leave the

motor running idle for approx. 5

minutes.

c. Remove the battery and check the

chain tension again. If necessary,

re-tighten the chain.

d. Afterwards make only easy cuts for

approx. 30 minutes. Always ensure



Only use the Nexxsaw for heavier cuts

and greater cutting depths after the

running-in period has expired.

• Use only sharp saw chains. Blunt saw

chains can jam more easily. Check the

chain tension more frequently when

working with new saw chains, as the



• The service life of a saw chain depends



tension.

• During operation, the chain heats up and

re-tensioning may be necessary. Relax

the chain after work so that it is not too

tight the next time the cold machine is

used.

• Do not re-tighten saw chains that have

become too hot. After it has cooled

down, it may contract and lie too tight

7063578-Nexxsaw-Ma-WoF-1910-08.indb 9 15-10-19 17:12

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-NXS001 - 7063578 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Batavia BT-NXS001 - 7063578 Manual

Product: